PRELIMINAR
Y
1
Extron PS 910, PS 1210, PS 1508 Series Installation Guide
About PS 910, PS 1210, PS 1508 Power Supplies
Model
Part
Number
Power Output
Termination
PS 910C
70-774-01
9 watts, 9 VDC, 1 A
Captive screw
PS 910P
70-777-01
9 watts, 9 VDC, 1 A
DC plug
PS 1210C
70-775-01
12 watts, 12 VDC, 1 A
Captive screw
PS 1210P
70-778-01
12 watts, 12 VDC, 1 A
DC plug
PS 1508C
70-776-01
12 watts, 15 VDC, 0.8 A
Captive screw
ZipClip
™
100
101-002-01
—
—
Connector pin assignments
Power Supply
Output Cord
Captive Screw
Connector
Ridged
Smooth
Tie Wrap
PS 910C, PS 1210C, PS 1508C
PS 910P, PS 1210P
Sleeve (-)
Tip (+)
Features
Power
LED
ZipClip Mounting Slots
Notches for Securing
Tie Wrap
Using the ZipClip 100
Attaching/removing the clip and power supply
To
attach
the power supply to the ZipClip 100 mounting clip:
1.
Insert the bottom of the power supply down into the clip,
starting with one end.
2.
Pivot the other end down and press until the clip snaps into
place.
To
remove
the power supply from the ZipClip:
1.
Press the ZipClip’s tab.
2.
Pivot the power supply
and lift it out of the
ZipClip.
1
2
Rack Mounting
Mounting to a rack shelf
These power supplies are one eighth rack wide. Up to eight power
supplies can be mounted side by side on a rack shelf.
1.
Align the threaded holes in the bottom of the power supply with
the holes in an Extron rack shelf and fasten the supply to the
shelf with two screws as shown below.
2.
Bolt the rack shelf to the rack.
Mounting to rack rails using a ZipClip
1.
Fasten the ZipClip 100 mounting clip to a rack beam using two
rack screws, as shown below.
2.
Insert the bottom of the power supply down into the clip, starting
with one
end.
3.
Pivot the
other end
toward
the clip
and press
until
the clip
snaps
into
place.
(2) 4-40 x 3/16"
Screws
VersaTools
®
Rack Shelf
Rack Mounted
1
2
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
Back of Rack
Side of Rack
Inside a Rack
Extron External Power Supply Installation Guide
68-1575-01
Rev. A
05 08
Pole or Table Leg Mounting
1.
Wrap a tie wrap around
the projector mount
pole or table leg and the
power supply at one of
the tie wrap notches,
and fasten the tie wrap
together to secure the
power supply to the
pole or table leg.
2.
Repeat step 1 at the
other tie wrap notch.
Tie Wrap to Pole
Using tie wraps for cable strain relief
1.
Attach the power supply to the ZipClip 100 mounting clip as
described previously.
2.
Fastening the power output cord to the ZipClip base.
a.
Insert tie wraps along the notches on the side of the power
supply and through the ZipClip’s tie wrap anchor points,
then around the cord.
b.
Connect pull the tie wrap until secure. Do not over tighten.
Cable
Strain
Relief
