background image

Input Audio and Video

The two pairs of buttons on the right of the screen allow three 
settings to be toggled On and Off.

Input Audio

 — Enables 2CH PCM support on input EDID. 

Input Audio is On by default.

HDCP Authorize

 — When this setting is enabled, 

HDCP-encrypted input signals pass to the output display. 
HDCP Authorize is On by default.

Aspect Ratio

 — Press 

Fill

 to stretch the image so that it 

fills the entire screen. Press 

Follow

 for the image to maintain 

the aspect ratio of the input signal.

Adjust Picture

 — Press 

Adjust Picture

 to open a 

dialog to adjust the input video picture. Press 

Brightness

Contrast

, or 

Detail

 to adjust those values. 

Active Pixels

 and 

Active Lines

 are 

read-only and cannot be edited.

Brightness

 — 

0

 to 

127

 (default 

64

)

Contrast

 — 

0

 to 

127

 (default 

64

)

Detail

 — 

0

 to 

127

 (default 

64

)

Active Pixels

 (status only)

Active Lines

 (status only)

Presets

 — Allows the current values to be saved as 

a preset and opens the 

Presets

 dialog (see figure 16, 

below).

Default all

 — Returns the picture values to their 

default settings.

Exit

 — Closes the dialog.

Presets

Save

Recall

Rename

Clear

Name

Input

#

1
2
3
4
5
6
7
8

HDMI
HDMI
N/A
N/A
N/A
N/A
N/A
N/A

Blu-ray
Blu-ray 2
Preset 03
Preset 04

Preset 08

Preset 07

Preset 06

Preset 05

Figure 18. 

Presets Dialog

Save

 — Highlight one of the presets and press 

Save

 to save the current Brightness, Contrast, 

and Detail settings to that preset.

Recall

 — Highlight one of the presets and press 

Recall

 to replace the current settings for 

Brightness, Contrast and Detail with those saved by that preset.

Rename

 — Highlight one of the presets and press 

Rename

 to assign a new name to the preset.

Clear

 — Highlight one of the presets and press 

Clear

 to clear the values stored by that 

preset.

Brightness

64

64

Contrast

Detail

64

Active Pixels

1280

Active Lines

720

Presets

Default

All

Exit

Input Audio and Video

Off

On

Input

Audio:

Off

On

HDCP

Authorize:

Follow

Fill

Aspect

Ratio:

Adjust Picture

 

TLI Pro 101 • On-screen Menus

20

Summary of Contents for TLI Pro 101










































Reviews: