Mounting
The following instructions are provided for experienced installers to mount the TLP Pro 300M touchpanel. The touchpanel can be
wall-mounted, either using a standard 1-gang, UL-listed electrical box (must be purchased separately), or directly into drywall or
furniture. Suitable mounting accessories can be found at
ATTENTION:
•
Do not install touchpanels in a fire resistant rated wall or partition assembly.
•
Ne pas installer les écrans tactiles sur un mur protégé par un dispositif coupe-feu ou dans une cloison.
•
All structural steps and electrical installation must be performed by qualified personnel in accordance with local and
national building codes and electrical codes.
•
Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualifié, conformément aux codes du
bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.
Mounting With a UL-listed Electrical Box
The UL-listed electrical junction box must be purchased separately.
1.
Cut a hole for the junction box at the required location.
2.
If you are using the provided tether kit to deter theft, one loop of
the tether kit should be secured to a wall stud with a screw (not
provided)
3.
Run cables to the installation site as required.
4.
Pass the other end of the tether kit and the cables
through a knock-out in the junction box.
5.
Install the junction box by following the instructions
provided by the manufacturer.
6.
Secure the metal mounting plate to the junction box,
using the provided screws.
7.
Attach cables to the back of the TLP Pro 300M (see
8.
If a tether kit is being used, loosen the security screw
on the back panel (see
F
, on page 3)
just enough to insert the loop of the tether kit.
9.
Tighten the screw to clamp the tether in place.
10.
Attach the touchpanel to the metal mounting plate. The
touchpanel is held in place by magnets.
NO
RTH
AMERIC
A
NO
RT
H
AMERIC
A
Wall
TLP Pro 300M
Metal
Mounting
Plate
Electrical
Junction
Box
#6-32 x ¾"
pan-head screws
Figure 1.
Mounting to a UL-Listed Electrical Box
Mounting to Drywall or Furniture
Figure 2 shows how to mount the TLP Pro 300M in drywall. Follow the
same procedure to mount into furniture.
1.
Download the TLP Pro 300M Cut-out Template from the Extron
website (
). Ensure that it is printed at 100% size,
with no scaling.
2.
Remove the cut-out area from the template.
3.
Attach the template to the wall in a suitable location, using a level to
ensure the template is aligned correctly.
4.
Use the template to mark and remove the cut-out area
(
1
) and drill two holes (
2
) for the screws that secure
the toothed clamping plates.
5.
If you are using a tether kit to deter theft, one loop of
the tether kit should be secured to a wall stud.
6.
Run cables to the installation site as required.
7.
Secure the metal mounting plate to the clamping
plates, using the provided screws. As the screws turn
they tighten the grip of the clamping plates on the
inside surface of the drywall.
8.
Attach the tether kit and cables to the touchpanel
and secure the touchpanel to the mounting plate as
described in steps 7 through 10 in the previous section.
NO
RTH
AMERIC
A
NO
RT
H
AMERIC
A
TLP Pro 300M
Wall
Metal
Mounting
Plate
Toothed
Clamping
Plate
#6-32 x 1½"
flat-head screws
1
1
1
2
2
2
Figure 2.
Mounting to Drywall or Furniture
2
TLP Pro 300M Series • Setup Guide (Continued)
