background image

On-screen Menus

On-screen menus allow initial configuration of the touchpanels. The figures in this section show 
screens for the TLP Pro 725T. Unless stated otherwise, the screens for the other touchpanels are 
very similar.

Setup Menu

To open the setup menu, use a screw driver with a fine blade to press the 

Menu

 button. The 

Menu button is located on the rear panel of the TLP Pro 525M, 725M, or 1025M (see 

figure 3

 

on page 8) or on the base of the TLP Pro 525T, 725T, or 1025T (see 

figure 5

 on the previous 

page).
The menus open at the 

Status

 screen. There are five different screens:

• 

Status

 (see below)

• 

Audio

 (see page 18)

• 

Network

 (see following page)

• 

Advanced

 (see page 19)

• 

Display

 (see page 17)

These can be selected by pressing the appropriate button in the navigation panel at the top of 
the screen. The button for the selected screen is yellow. The buttons for the remaining screens 
are black.
There is also a red 

Exit

 button in the top right corner of the screen. Pressing this button applies 

and saves any changes and closes the menu screens.

Status

Press the 

Status

 button in the navigation panel at the top of any screen to open the 

Status

 

screen.

Status

Display

Audio

Advanced

Exit

Network

Info

Model:

TLP Pro 725T

Part Number: 60-1562-02
Firmware

Version:

1.00.0001-b003

Network

IP Address:
DHCP:
Host Name:

Off

192.168.254.251

TLP-AB-CD-EF

Display

Resolution:
GUI Project:
Sleep Timer:

1024x600
N/A
5 Minutes

Audio

Master Volume:
Master Mute:

Off

99

Advanced

Controller IP:

N/A

Project Size:

N/A

Bootloader

Version:

1.00.0000

Figure 6. 

Status Screen

The 

Status

 screen is a read-only screen that provides basic information about the touchpanel. 

Each of the other four panels shows a summary of the information on the other screens.
Pressing any of the panels opens the corresponding screen in exactly the same way as pressing 
the buttons in the top navigation panel.
A green bubble in the 

Network

 panel lights when there is a network connection or a red square 

appears if there is no connection. The green bubble in the 

Advanced

 panel lights when a control 

processor is connected or a red square appears if none is connected.

TLP Pro 525, 725, and 1025 Series Touchpanels • On-screen Menus

14

Summary of Contents for TouchLink Pro













































Reviews: