EZ-ACCESS Pathway Modular Gate Assembly Manual Download

Page: 3 / 10

- 3 -

BASIC SYSTEM COMPONENTS

1.1.

Because each installation is different, your system may or may not contain these basic components.

1.2.

Ensure all components listed are present prior to assembly.

1.3.

NOTE: Items not shown actual size.

PATHWAY 3G UNIVERSAL GATE

(QTY 1)

1/4”-20 X 2” LONG HEX CAP SCREW

(QTY 3)

#8-

32 X 1/2” LONG HEX WASHER

HEAD THREAD CUTTING SCREW

(QTY 7)

1/4

” -20 LOCKNUT (QTY 3)

1/4” FENDER WASHER (QTY 6)

GRAVITY LATCH (QTY 1)

Includes Latch & Latch Bar

1/2” DIAMETER TUBE PLUG

(QTY 4)

5/16”-18 X 5” HEX BOLT

(QTY 1)

1/4”-20 X 3/4” HEX BOLT

(QTY 3)

Used for Pathway Modular

Stair

installation only

Used for Pathway Modular

Stair

installation only

5/16”-18 X 3/4” HEX BOLT

(QTY 2)

5/16”-18 LOCKNUT

(QTY 2)

PATHWAY STAIR TO GATE

MOUNTING ADAPTER (QTY 1)

Used for Pathway Modular

Stair

installation only

Used for Pathway Modular

Stair

installation only

Used for Pathway Modular

Stair

installation only

Summary of Contents for Pathway Modular Gate











Search results

Summary of Contents for Pathway Modular Gate

Reviews:

Related manuals for Pathway Modular Gate

Brands by name

Popular brands

EZ-ACCESS Pathway Modular Gate, Assembly Manual

Search results

Summary of Contents for Pathway Modular Gate

Reviews:

Related manuals for Pathway Modular Gate

Brands by name

Popular brands