background image

 

Do not commence installation until you have read and understood the instructions 
and warnings contained in this installation sheet.  If you have any questions 
regarding any of the instructions or warnings, please contact your place  
of purchase.

 

This mounting bracket was designed to be installed and utilised ONLY as 
specified in this manual.  Improper installation or use of this product may  
cause damage or serious injury.

 

This product should only be installed by someone of good mechanical ability,  
with basic building experience and full understanding of this manual.

 

Make sure that the supporting surface (i.e. wall) will safely support the combined 
load of this bracket and all attached hardware (TV) and components.

 

If mounting to timber wall studs, make sure that the mounting screws are 
anchored into the centre of the studs. Use of a stud finder is highly recommended.

 

Always use an assistant or mechanical lifting equipment to safely lift and position 
equipment.

 

Tighten screws firmly, but do not over tighten. Over tightening can cause damage, 
greatly reducing their holding power.

 

This product is intended for indoor use only. Using this product outdoors  
could lead to product failure and personal injury.

 WArNINg

NOTE:  Please read the entire instruction manual before you start  
 

installation and assembly

Summary of Contents for SLT-800









Reviews: