CHD 12V PLUS
| English
10
2. Or by the in-line support grip.
DRILLING WOOD AND PLASTIC
To prevent splitting around the drill holes on the re-
verse side, place a piece of scrap timber under the
material to be drilled.
DRILLING METAL
Metals such as sheet steel, aluminium and brass may
be drilled. Mark the point to be drilled with a centre
punch to help the drill bit tip to locate. A drop of oil
on the area will aid cutting and help prolong the life
of the bit.
DRILLING MASONRY
Start drilling at a low speed to prevent the drill bit
from wandering. Once penetration is achieved, fully
depress the trigger to achive maximum speed and
hammer power.
SCREWDRIVING
To prevent slip or damage to the screw head, match
the screwdriver bit to the screw head size. To re-
move screws, move the direction switch to the re-
versing position and apply pressure to the screw
head and depress the trigger slowly).
Screwdriver bits are a consumable item. Before drill-
ing check that there are no hidden hazards such as
electrical cables, water or gas pipes running below
the surface by use of a metal/voltage detector. Do
not expose either the drill or charger to rain or wa-
ter.
Do not overcharge the battery (more than six hours)
as this could damage the battery cells.
TROUBLESHOOTING
NOTE:
Remove plug and/or battery before carry
-
ing out any adjustment, servicing or maintenance.
Problem
Cause
Remedy
Drill does
not work
1. Flat battery.
2. Forward/
Reverse not
selected.
1. Charge bat-
tery.
2. Select
forward or
reverse.
Chuck
does not
close or
grip
1. Lock screw
loose.
2. Swarf in
chuck.
1. Open chuck
fully and
tighten screw
(left hand
thread).
2. Clean inside
chuck with
cleaning fluid.
MAINTENANCE
Regular inspection and cleaning reduces the ne-
cessity for maintenance operations and will keep
your tool in good working condition. The motor
must be correctly ventilated during tool operation.
For this reason avoid blocking the air inlets.
HANDLING & STORAGE
Although this machine is small in size, care must still
be taken when handling and lifting. Dropping this
machine will have an effect on the accuracy and may
also result in personal injury. This machine is not a
toy and must be respected.
The environment will have a negative result on its
operation if you are not careful. If the air is damp,
components will rust. If the machine is unprotect-
ed from dust and debris; components will become
clogged: And if not cleaned and maintained cor-
rectly or regularly the machine will not perform at
its best.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
as waste. Machine, accessories and pack-
aging should be sorted for environment -
friendly recycling. The plastic components
are labeled for categorized recycling.
GUARANTEE
This product is warranted in accordance with the le-
gal/country specific regulations, effective from the
date of purchase by the first user. Damage attribut
-
able to normal wear and tear, overload or improper
handling will be excluded from the guarantee. In
case of a claim, please send the machine, completely
assembled, to your dealer or the service Centre for
electric power tools.
Summary of Contents for 41306
