www.ffgroup-tools.com
English | 9
P 750 PLUS
www.ffgroup-tools.com
f
Hold the power tool by insulated gripping surfaces
only, because the cutter may contact its own cord.
Cutting a ”live” wire may make exposed metal parts
of the powertool ”live” and could give the operator
an electric shock.
f
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by your hand or against the body
leaves it unstable and may lead to loss of control.
CONNECTION TO THE POWER SUPPLY
Make sure the power supply information on the ma
-
chine's rating plate are compatible with the power
supply you intend to connect it to.
This appliance is Class II and is designed for connec-
tion to a power supply matching that detailed on the
rating label and compatible with the plug fitted. If
an extension lead is required, use an approved and
compatible lead rated for this appliance. Follow all
the instruction supplied with the extension lead.
GUIDELINES FOR USING EXTENSION CORDS
f
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
f
Always replace a damaged extension cord or have it
repaired by a qualified person before using it.
f
Protect your extension cords from sharp objects, ex-
cessive heat and damp/wet areas.
f
Use a separate electrical circuit for your tools. This
circuit should be protected with the appropriate
time-delayed fuse. Before connecting the motor to
the power line, make sure the switch is in the OFF
position and the electric voltage is rated the same as
the voltage stamped on the motor nameplate. Run
-
ning at a lower voltage will damage the motor.
PRODUCT
SPECIFICATIONS
INTENDED USE
This tool is intended for planing wooden materi-
als such as beams and boards; it is also suitable for
chamfering edges and rabbeting.
TECHNICAL DATA
Article number
43 011
Model
P 750 PLUS
Rated voltage
V
230/240
Hz
50
Power
W
750
No-load speed
min
-1
17.000
Max planing width
mm
82
Planing depth
mm
0-2
Rebating depth
mm
18
Weight
kg
2,9
Sound emission values determined according to
EN 62841-1, EN 62841-2-14
Typically the A-weighted noise levels of the product are:
Sound pressure level
dB(A)
92,2
Sound power level
dB(A)
103,2
Uncertainty K
dB
3
Vibration total values a
h
(triax vector sum) and
uncertainty K determined according to
EN 62841-1, EN 62841-2-14
Vibration level max:
a
h
m/s
2
4,34
K
m/s
2
1,5
IDENTIFICATION
1.
Handle
2.
Ventilated motor housing
3.
Rebating depth guide
4.
Rebating depth guide locking lever
5.
Trigger lock button
6. Power trigger
7. Chip ejector selector button
8. Planing depth adjuster with scale
9.
Parallel guide locking knob
10. Soleplate
11. Power indicator, lights when planer is energized
12. Blade tool holder
13. Drive belt cover
14. Chip ejector
15. Parallel guide
16. Blade
17. Drum plate
18. Clamping screw
19. Set plate
20. Set screw
21. Blade drum
22.
Parking rest
23. Springloaded guard
24. Dust bag
OPERATION INSTRUCTIONS
WARNING:
Always unplug the planer before adjusting the
cutting depth or cutting width.
Make sure that the workpiece is securely fas
-
tened to the work bench and that the work bench
is stable and won’t move.
Lower the parking rest
(22)
on the rear of the
planer when you stop work. It protects the blade
when it is not in use
(image
D)
.
PLANING A FLAT SURFACE
Turn the planing depth adjuster
(8)
to the desired
depth. Plug the planer into the wall socket. Hold in the
trigger lock button
(5)
and then pull the power trigger
(6)
.
WARNING:
Never adjust the planing depth while
planing; doing so will result in an uneven depth of
cut. Always return the planing depth to 0 when you
Summary of Contents for 43 011
