F.F. Group DSL 710 PLUS, Original Instructions Manual

DSL 710 PLUS

English   | 11

www.ffgroup-tools.com

Sanding sheet size

mm

225

Weight

kg

4,5

Sound emission values determined according to 

EN 60745-1

Typically the A-weighted noise levels of the product are:

Sound pressure level

dB(A) 

79,9

Sound power level

dB(A) 

90,9

Uncertainty K

dB

3

Vibration total values a

h

 (triax vector sum) 

and uncertainty K determined according to EN 

60745-1

Vibration level max:

a

h ,HD

m/s

2

2,254

K

m/s

2

1,5

IDENTIFICATION

1.  Locking sleeve (for connecting vacuum clean-

er/extension tube)

2. 

On/off locking switch

3.  Sanding speed selection wheel

4.  Sanding hose

5.  Pad cover segment

6. 

Backing pad (VELCRO)

7.  Sanding disc

8. 

Flexible hose + vacuum cleaner adapter Ø 57 

mm

9.  Auxiliary handle

10. 

Vacuum cleaner adapter Ø 47 mm

11. 

Vacuum cleaner adapter Ø 35 mm

12.  Double-ended screwdriver

13.  Hex key

HEAD ASSEMBLE INSTRUCTION

A.  Cut the plastic buckle and loosen the 

plastic tape.

B.  The aluminum pipe under black transmit-

ting wire. Place the transmitting wire into 

the hole in the middle of plastic plate.

C.  Revolve the plastic plate to ensure the 

transmitting wire is tightly closed to the 

plastic plate.

D.  Fix nut by using of wrench ,then loosen 

screw by using of screwdriver.

E.  Place the bend aluminum pipe into the 

hole, then fix it by screw and nut.

F.  Fix the flexible pipe into the aluminum 

pipe with ring by using of screwdriver.

G.  The head of Drywall Sander is assembled.

REPLACEMENT OF SANDING PAPER

Backing pads 6

Never run the tool without backing pad 

6

ƒ

Replace  damaged  backing  pads  immediately 

(loosen/fasten pad screw with hex key 13).

ƒ

Unplug tool before removing/mounting back-

ing pads.

Mounting sanding discs 7

ƒ

Simply press sanding disc 

7

 onto backing pad with 

perforation in sanding disc corresponding with 

perforation in backing pad. If necessary, clean 

backing pad first

ƒ

The dust suction requires the use of perforat-

ed sanding discs.

REPLACEMENT OF GRINDING DISK STUCK

The output shaft is inserted into the adhesive disc 

center with six angle wrench clockwise rotation 

angle in the six-hex, and at the same time, the 

hands hold the adhesive disc grinding, grinding 

disc can be remove adhesive.

SPEED ADUSTMENT 

The grinding of the grinding disk rotation speed 

can be adjusted according to different conditions 

and grinding quality requirements.

The Drywall Sander is equipped with a variable 

speed control. The speed is adjusted by turning 

the control knob. The control knob is numbered 

"ΜΙΝ" through "ΜΑΧ" with "ΜΙΝ" being the slow

-

est speed (Approximately 1000 RPM) and "ΜΑΧ" 

being the fastest speed {approximately 2200 

RPM).

Use the higher speed settings for fast stock re-

moval. Use the lower speed selling to reduce re-

moval rate for more precise control.

DUST SUCTION

f

Loosen locking sleeve 

1

 by turning it in the direc-

tion of the unlocking symbol on the tool handle.

f

Insert flexible hose 

8

 into the end of the tool han-

dle as illustrated.

f

Tighten locking sleeve 

1 

by turning it in the direc-

tion of the locking symbol on the tool handle.

f

Connect  the  flexible  hose  with  the  Ø  57  mm 

adapter directly to an industrial vacuum cleaner 

(remove vacuum cleaner hose first).

f

One  may  also  connect  flexible  hose 

8

 with one 

of the 3 adapters to an industrial vacuum cleaner 

without removing the vacuum cleaner hose.

f

For  mounting  vacuum  cleaner  adapter 

10

 or 

11

use screwdriver 

12

 as illustrated.

TO START AND STOP DRYWALL SANDER

Make sure power circuit voltage is the same as 

shown  on  the  specification  plate  on  the  Sander, 

and that the Sander switch is OFF. Connect Sander 

to power circuit.

The top end of the switch button is labeled "Ο", 

and the bottom end of the switch button is la-

beled "Ι". 

Τo start the sander: 

Press switch for-

ward to the position "I" and then press it down to 

lock. 

To stop the sander:

 press the switch back to 

the position "O".

HOLDING AND GUIDING THE TOOL

The drywall sander has a unique sanding head. 

The head can swivel in multiple directions, allow-

ing the abrasive pad to conform to the work sur-

face. This enables the operator to sand the top, 

middle and bottom of a wall or ceiling joint with-

out changing: his position.

f

Always hold the tool firmly with both hands.