| English
14
Items
B
ef
o
re e
ac
h u
se
A
ft
er 1
st m
o
nt
h o
r 5
hr
s o
f
op
er
at
ion
Ev
er
y 3 m
o
nt
hs o
r 2
5h
rs
of
op
er
at
ion
Ev
er
y 6 m
o
nt
hs o
r 5
0
hr
s
of
op
er
at
ion
Ev
er
y 1
2 m
o
nt
hs o
r 1
0
0
hr
s
of
op
er
at
ion
Εngine oil
Check -
Refill
√
Replace
√
√
Gearbox oil
Check -
Refill
√
Replace
√**
Linkages
Lubricate
√
Air filter
Check -
Clean
√*
√*
√*
Replace
√
Spark plug
Check -
Adjust
√*
Replace
√
Fuel filter
Clean
√
Fuel tube
Check
√*
Carburator
sediment
cup
Clean
√
Valve clear
-
ance
Check -
Adjust
√**
*These items should be replaced if needed.
**These items should be maintained and repaired only by
authorised dealer, that have the appropriate tools and the
required mechanical proficiency.
TILLING TOOL
Periodically check tilling tines for wear or damage.
Damaged parts must be replaced before operating
the tiller again. Tilling knives wear will negatively af
-
fect tilling capability of the machine and they should
be replaced if required.
CLUTCH, REVERSE AND THROTTLE LEVERS PLAY
Small adjustments on the already pre-assembled
clutch, reverse and throttle cables can be done by
using the nut and rod screw on each cable at the
side of the lever. If the travel distance in not correct,
loose the lock nut and adjust by play by turning the
adjustment bolt as required. When finished, tighten
the lock nut and check again for proper clutch lever
operation.
After any related adjustment, make sure that the
clutch, reverse or throttle levers move from one
position to another without the need for excessive
force and that the clutch, reverse or throttle rods on
the gearbox or engine respectively can be operated
to their full range.
NOTE:
It is recommended that such adjustments are only
performed by trained personnel at your nearest deal-
er shop, to ensure the original safety standards of the
machine.
Frequency
LUBRICATION
WARNING:
Checking the level and changing the oil should be done
on solid and level ground. The engine has to be stopped
at all times. If the engine had been running, it will be hot
and the procedure should be done with care and neces-
sary precautions in order to avoid burn danger.
NOTE:
Drain the used oil while the engine is warm. Warm oil
drains quickly and completely.
Engine oil
To check the oil level:
1. Remove the oil filler cap from the engine oil filler
neck.
2. Wipe the oil level indicator clean.
3. Insert the oil filler cap into the oil filler neck, with
-
out screwing it.
4. Remove the filler cap and check the oil level
shown on the oil level indicator. If required, add
enough oil to bring the oil level between the up-
per and lower limit on the oil level indicator.
5. Reposition the oil filler cap and tighten appropri
-
ately.
To change the oil:
1. Remove the oil filler cap from the engine oil filler
neck.
2.
Place a suitable container under the oil drain plug
(Fig. 8.1) to catch the used oil.
3. Remove the oil drain plug and allow the oil to
drain completely.
4. Reposition the oil drain plug and tighten appro
-
priately.
5. Gradually add enough oil to bring the oil level be
-
tween the upper and lower limit on the oil level
indicator.
6. Reposition the oil filler cap and tighten appropri
-
ately.
NOTE:
If the engine frequently works under extremely dusty
or other severe circumstances, change the engine oil
every 25 hours.
WARNING:
Running the engine will low oil level will cause engine
damage.
Gearbox oil
To check the oil level:
1. Remove the oil filler cap from the gearbox oil filler
neck.
2. Check the oil level. If required, fill with enough oil
to bring the oil level between the upper and lower
limit on the oil level indicator.
3. Place the oil filler cap in position and tighten ap
-
propriately.
To change the oil:
Gearbox oil change operation should be done by
your Dealer or a specialized Service Centre with the
necessary knowledge and equipment.
WARNING:
Running the tiller will low gearbox oil level will cause
gearbox damage.
Linkages lubrication
Lubricate the linkages every ten hours of opera
-
GTL 900 PRO | GTL 1250 PRO | GTL 1500 PRO
Summary of Contents for GTL 900 PRO
