background image

9

ENGLISH

ENGLISH

2. PROGRAMMING

To program operation of the automated system, you have to
access the “PROGRAMMING” mode.
Programming is split into two parts: BASIC and ADVANCED.

2.1 HOW TO ACCESS PROGRAMMING

To access 

BASIC PROGRAMMING, when on stand-by, press key 

F

(the first basic function is shown).
To access 

ADVANCED PROGRAMMING, when on stand-by or from

inside basic programming, press key 

F

 and, while you hold it down,

press key 

+

 (the first advanced function is shown).

If you release key 

F

 (basic programming) or  

F

 and 

+

 (advanced

programming), the value of the current function is shown, and
can be modified with push-button 

+

 or 

-

.

Next:
• if you press 

F

 (and hold it down), the display shows the name of

the next function;

• if you release key 

F

, the display shows the value of the function

which can be modified with keys 

+

 and 

-,

  etc….;

• at the end, Digiprogram returns to stand-by mode.
The following tables indicate the sequence of functions accessible
with BASIC PROGRAMMING and ADVANCED PROGRAMMING.

+

+

F

TIME LEARNING (see chapters 4 and 5)

Enables the selection between “simple” (automatic)
learning and “complete” (manual choice of
deceleration and stop points) learning.

Note: wait for the 

 to light up steady after a few

seconds of flashing, before starting the learning cycle.

Simple learning

 

 

 

 

 

1 sec.

Complete learning

>  3 sec.

Exit without time learning

LEAF 1 CLOSING DELAY

Delays closing start of leaf 1 with respect to leaf 2.
Programmable

from

 to 

 minutes (for the

adjustment mode, see Pause time).

LEAF 2 FORCE

Adjusts thrust of Motor 2.
Programmable

from

    (minimum force)

to

 (maximum force)

LEAF 1 FORCE

Adjusts thrust of Motor 1.
Programmable

from

    (minimum force)

to

 (maximum force)

PAUSE TIME

This has effect only if an automatic logic was selected.
Adjustable from   to 

 sec. in one-second steps;

subsequently, display changes to minutes and tens of
seconds (separated by a dot) and time is adjusted in 10-
second steps, up to the maximum value of 

 minutes.

E.g. if the display shows 

, pause time is 2 min. and 50

sec.

FUNCTION LOGICS

= Automatic
= Semi-automatic
= “Safety”  Automatic

= “B” Semi-automatic

= Dead-man
= “Stepped” Automatic

=“Stepped” Semi-automatic
=”Stepped” Safety Automatic

BASIC PROGRAMMING

Digiprogam is an external programmer used for configuring the
462F control board.

1. DIGIPROGRAM CONNECTION

Using the supplied cable, connect Digiprogram to board 462DF
as shown in fig. 1.  Digiprogram has no internal battery of its own
because it is powered directly by the control board.
As soon as it is connected, the Digiprogram display shows 

 for

two seconds to let you check if all segments and dots are correctly
powered up. After this, the Digiprogram goes into stand-by,
displaying the status of inputs (see Chapter 3).

ATTENTION: the safety devices are disabled
during the learning procedure! Therefore,
carry out this operation avoiding any transit
through the leaf movement area.

F

Display

Function

Default

fig.1

Summary of Contents for Digiprogam









Reviews: