FAAC E012 Instruction Manual Download | Manualshive

Page: 10 / 16

background image

Page 10

Rev. 01.2006 - Istallation Manual

2.3.1

AN ESSENTIAL CONTROL

If you are not using safety devices (photocell, pressure switch, edge, etc..) or pulse generators (push-
button, key selector, etc..), make sure that cursors 6 and 7 on the dip-switch are disabled (position "ON").
If you decide to disable these commands, you do not have to jumper the input.
This control is essential, otherwise the motor will not start.

IMPORTANT: The dip-switch cursors are shown in white in the following drawings.

2.4

WIRING OF (OPTIONAL) ACCESSORIES

B A T T E R I E S

TOROIDAL TRANSFORMER

POWER SUPPLY TO EXTERNAL

ACCESSORIES

E A R T H

MOTOR 1

MOTOR 2

ELECTRIC LOCK 12V

FLASHING LAMP
COURTESY LIGHT

RECEIVER

OTHER CLOSING

SAFETY DEVICES

5-PIN RECEIVERS

CONNECTOR

MAX 1 PAIR FSW

«
...
8
9
10
11
12
...
»

Summary of Contents for E012

















Reviews:

No comments

Related manuals for E012

Brand: Samson Pages: 78

Brand: Rachio Pages: 16

Brand: unicore Pages: 25

Brand: unicore Pages: 24

Brand: Aalborg Pages: 128

Brand: Accel Pages: 8

Brand: H-P Products Pages: 12

Brand: RAKwireless Pages: 6

Brand: hager Pages: 2

Brand: hager Pages: 4

Brand: DSEGenset Pages: 74

Brand: ITALFARAD Pages: 32

Brand: W.E.ST. Pages: 34

Brand: Ltech Pages: 4

Brand: Motor Guard Pages: 2

Brand: K&K Pages: 6

PersonalWorkplace Pro Video

Brand: G&D Pages: 56

Brand: Beninca Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands