background image

7

ENGLISH

ENGLISH

                

All the components of an exit lane of a ParkLite automated 

parking system, are directly managed by the Ticket Dispenser.

The exit lane of a parking area consists of:

• 

Nr. 01 ParkLite Ticket Reader.

 

Nr. 01 620 rapid barrier RH.

 

Nr. 02 Magnetic loops.

 

Nr. 01 Pair of photocells.*

  The exit lane from a parking area managed by the Ticket 

Reader must be constructed so that the vehicles coming from 

different directions can easily get close to the column, to 

enable the user to read the ticket or a valid card without any 

difficulty.

•  

The equipment must be installed on an island 15 cm. above 

road level. If this is not possible, protective structures must be 

installed around the base of the two columns (TR and barrier 

620) and the Ticket Reader must be raised 15 cm. above the 

lane paving, so that the devices for reading and treating the 

tickets for exit from the parking area are located at the right 

height.

•  

The Ticket Reader operates only if the magnetic loops have 

been correctly connected to it. In fact, the column was desi-

gned to manage all the user exit from lane stages, exploiting 

these two elements, which are generally defined as: presence 

loop and transit loop. 

fig. 2 Exit lane

The construction and deployment of the loops is fundamentally 

important to ensure that the system functions correctly. For this 

reason, observe to the letter all the instructions described in the 

following paragraphs:

2.3 Making the Magnetic Loops

2.7 Positioning the equipment.

•  

 The power cables and the cables for connecting the equi-

pment in the parking system must have the characteristics 

indicated in paragraph:

3.2 Type of cables.

Furthermore, all the instructions in paragraph “General safety 

rules” on page 3 must be respected, and, with reference to the 

specific electrical preparations, as described in paragraph:

3.1 Safety rules.

•  

The Ticket Reader was designed to manage automatically 

the exit of vehicles from a parking area. Therefore, transit by 

pedestrians must be forbidden in the area reserved for transit 

of vehicles. Moreover, appropriate signs prohibiting transit by 

pedestrians must be installed. Where it is not possible to have 

an entrance/exit gate reserved exclusively for pedestrians, the 

current legal regulations on the subject must be absolutely 

observed; (in particular standards: EN 12453 and EN 12445)

•  

The lane must not allow the exit by two or more vehicles 

side by side. For this reason, the width of the lane must be 

appropriately sized, according to the type of vehicle generally 

used.

•  

Sufficient space must be provided for every equipment of 

the parking system, so that all the necessary installation and 

maintenance operations can be smoothly carried out.

•  

Position the Ticket Reader so that it (laser scanner) is not 

directly exposed to luminous radiation, which could be source 

of disturbance during reading.

•  

Appropriate signs (not supplied by FAAC), indicating the 

tariffs and the car park rules must be visibly shown on the 

entrance lane to the car park.

* optional

NB.: 

All the equipment which can be used in the ParkLite 

parking system, were designed and tested by FAAC, in 

observance of the points mentioned above. In order to avoid 

any kind of unforeseen behaviour, all the rules shown in this 

manual must be observed. 

2.2 ESSENTIAL REQUIREMENTS

  620 rapid barrier RH

 Photocells

      Magnetic        

Loops

 Ticket Reader 

 2.  INSTALLATION OF COMPONENTS

 2.1  LANE CHARACTERISTICS

Summary of Contents for ParkLite TR


















Reviews: