Faber FWH OTTIMO 501CH Instruction Manual Download

Page: 4 / 12

2. PRODUCT INTRODUCTION

NOTE

This manual is applicable to the instant electric water heaters manufactured by this

company. The nomenclature of the product is complied according to the Malaysia

Standard.

2.1 Technical Performance Parameters

Model

Rated Voltage

Rated Frequency

Rated Power

Rated Current

Dia. Of Wire Core

Air Switch

Rated Pressure

Minimum Flow Rate

Minimum Pressure

Maximum Pressure

Protection Class

Water Proof Class

Products Size

Knob Quantity

3800W

16A

4mm²

≥20A

SPLASH series OTTIMO series

240V~

50Hz

0 MPa

2 Liters/minute

0.03 MPa

0.3 MPa

IP25

200×400×97 mm

WARNING

The water heater should be earthed before use. Please ensure that the resistance of

household earth wire

is <4Ω.

Using water heater without earthed is highly prohibited.

Summary of Contents for FWH OTTIMO 501CH













Search results

Summary of Contents for FWH OTTIMO 501CH

Reviews:

Related manuals for FWH OTTIMO 501CH

Brands by name

Popular brands

Faber FWH OTTIMO 501CH, Instruction Manual

Search results

Summary of Contents for FWH OTTIMO 501CH

Reviews:

Related manuals for FWH OTTIMO 501CH

Brands by name

Popular brands