9
Cleaning metal grease filters
The metal grease filters can be cleaned in hot detergent
solution or washed in the dishwasher. They should be
cleaned every 2 months use, or more frequently if use
is particularly heavy.
•
Remove the filter, pushing the lever towards the back
of the unit and at the same time pulling downward.
•
Wash the filter without bending it, leave it to dry
thoroughly before replacing (if the surface of the filter
changes color over time, this will have absolutely no
effect on its efficiency).
•
Replace, taking care to ensure that the handle
faces forward.
•
Cleaning in dishwasher may dull the finish of
the metal grease filter.
Replacing Activated Charcoal Filter
The Activated Charcoal Filters are not washable
and cannot be regenerated, and must be
replaced approximately every 4 months of
operation, or more frequently with heavy usage.
• Remove the grease filters.
• Remove the saturated carbon filter.
• Fit the new filter by hooking it into its seating.
• Replace the grease filters.
Replacing the bulbs
E-14 Base 28 W halogen.
• Remove the metal grease filters.
• Replace the bulb with a new one of the same
type.
• Replace the metal grease filters.
EN
77
INSTALLATION
Fitting the Hood canopy
BEFORE FITTING THE HOOD TO THE WALL UNIT, PROCEED AS FOLLOWS:
• Disconnect the wires to the Commands at the connectors.
• Disconnect the wires to the Light at the con-
nectors.
• The Hood can be installed directly on the
underside of the wall unit (Minimum 650 mm
from the Cooker Hob).
• Create an opening in the bottom of the wall unit,
as shown.
• Insert the hood until the side supports snap into
place.
• Fasten using the 10 screws
12a
provided.
• Lock in position by tightening the screws
Vf
from
underneath the hood.
• Open the suction panel by turning the specific knob.
• Disconnect the panel from the hood canopy by sliding the
fixing pin lever.
• Remove grease filters.
• Screw the Frame into place
using the 6 screws
12f
, re-
connect the wires to the
Commands and Light, re-
place the metal grease filter
and the Panel.
260
13
495 - 675
Version 09/14 - Page 6
RECIRCULATING INSTALLATIONS
For recirculating installations
(FIGURE 1)
,
Charcoal Filters
are necessary. The
(A in FIGURE
1)
. Recirculating installations also require some duct work to divert the air out of the
cabinet. The duct work must not terminate inside the cabinet.
MAKE YOUR CUT-OUTS
1.
Disconnect and move freestanding range from cabinet opening to provide easier
access to upper cabinet and rear wall. Put a thick, protective covering over cooktop,
set-in range or countertop to protect from damage or dirt.
2.
Determine and clearly mark with a pencil the center line on the cabinet where
the rangehood will be installed.
3.
Determine and make all necessary cuts in the wall for the ductwork. Install the
ductwork before the rangehood.
4.
Determine the proper location for the Power Supply Cable. Use a 1
1/4"
Drill Bit
to make this hole. Install the cable. Use caulking to seal around the hole. DO NOT
turn on the power until installation is complete.
5.
Make the cut-out opening where the rangehood will be installed
(FIGURE 2)
.
26 21/32" WIDTH FOR 28" HOOD, 19 19/32" WIDTH FOR 24" HOOD
INSTALL THE RANGEHOOD
1.
-
face to prevent accidental damage. Remove all parts including the backdraft damper,
g the carton.
2.
Place the round damper into the exhaust opening of the rangehood and press
down.
3.
Remove the bottom of the rangehood by pulling on the grey tabs
(A in FIGURE
3)
located on either side.
4.
Fix the rangehood to the cabinet using the two spring loaded brackets, one on
each side of the rangehood
(B in FIGURE 4)
. Using a philips screwdriver, tighten
the adjustment screw
(C in FIGURE 4)
until the brackets adhere tightly to the surface.
For thicknesses of LESS than
3/4",
the cabinet bottom and the spring loaded bracket.
5.
IMPORTANT:
(FIGURE 4)
.
6.
Replace the bottom of the rangehood and secure by pushing in the grey tabs
(A
in FIGURE 3)
.
7.
Feed the Power Supply Cable through the electrical knockout. Connect the Power
Supply Cable to the rangehood cable. Attach the White lead of the power supply
to the White lead of the rangehood with a twist-on type wire connector. Attach the
Black lead of the power supply to the Black lead of the rangehood with a twist-on
type wire connector. Attach the Power Supply Cable grounding lead to the green screw
.
)
d
e
d
i
v
o
r
p
t
o
n
s
w
e
r
c
s
(
n
o
it
a
c
o
l
e
l
b
a
C
y
l
p
p
u
S
r
e
w
o
P
r
u
o
y
y
b
d
e
t
a
t
ci
d
s
a
t
e
n
i
b
a
c
r
o
Replace the cover.
8.
Connect the ductwork to the damper and seal all connections with duct tape.
9.
Turn the power supply on. Turn on the blower and light. If the rangehood does
not operate, check that the circuit breaker is not tripped or the house fuse blown. If
the unit still does not operate, disconnect the power supply and check that the wiring
connections have been made properly.
FIGURE 1
FIGURE 2
FIGURE 4
FIGURE 3
FIGURE 7
A
5” round
duct
cabinet
ceiling
inca smart
cabinet
ceiling
5” round
duct
inca smart
A
Install a grille or louver vent at the air outlet.
Cabinet min
H=30”
