EN
Suggested Pan dimensions for induction hob
The cooking zones are, up to a limit, automatically adapted to the diameter of the pan. However, the bottom of
this pan is suggested to have a minimum of diameter according to the corresponding cooking zone. To obtain
the best efficiency of your hob, please place the pan in the center of the cooking zone.
Base diameter of the pots:
Cooking zone
Minimum (mm)
Maximum (mm)
160mm
140
160
180mm
140
180
210mm
160
210
280mm
230
280
Flexible zones
200
400 x 200
Using your Hob's control panel
To start cooking
1. After the hob be connected to electricity and power on. Press and hold the ON/OFF
control button for about 3 seconds till you hear a “beep” to turn the hob on. Now the hob
enters into Standby mode, all heat setting indicators and Timer setting indicators shows
“-”
2. Place a suitable pan on the cooking zone you wish to use.
• Make sure the bottom of the pan and the surface of the cooking zone are clean and
dry.
3. Set heating level of cooking zone.
For model SVH 646 Black:
• There is separate "+" and "-" heat level control button for each cooking zone for these models. Set heat setting
by touching the "+" or "-" button for corresponding cooking zone.
• If press and hold either of the two "+" or "-" buttons, the value will adjust down or up rapidly, from 0 to 9 in circle.
For other models:
Before adjust heating level, need to touching the heating zone selection control button
to select and active the cooking zone you wish to use. The heat setting indicator of the
selected zone flashing when be active, then you could adjust its heat level by below
• adjust heat setting by sliding the slider control.
Notes:
1. After connect to electricity, when power on, the buzzer of hob beeps once, all indicators light up for 1 second
then go out.
2. When the hob in Standby mode, if there is no practice within 1 minute, the electric hob will auto turn off, with
buzzer beeps once.
3. To turn on hob, press the ON/OFF control button and hold on for about 3 seconds; To turn it off, just need to
press ON/OFF button again.
4. The power level can be adjusted from 0 to 9, default setting is level 5.
5. The heat setting indicator of the selected zone flashing when adjusting.
After adjusting, the number flashing for 5 seconds then stop flashing,
then the setting is be confirmed.
Summary of Contents for SVH 326
