Fabtech FT22179i Installation Instructions Manual Download

Page: 8 / 16

25. Install a ½” -13 x 4” bolt, washers and nut through the

tabs on the rear crossmember and the bushing on the
center bracket. Leave loose at this time.

SEE FIGURE 28

22. Locate the center differential bracket (FT30645). Install

two of the Fabtech (FT1020) bushings and one sleeve
(FT181) into the barrel on the differential bracket.

SEE FIGURE 24

23. On the front axle tube, remove the rear and lower bolts

to allow for the new center differential bracket to be
mounted.

24. Mount the differential bracket to the center of the

differential using three M10-1.5 x 45mm bolts, lock
washers, and flat washers. Mount the front tab on the diff
to the center bracket using one ½”-13 x 2” bolt, nut and
washers. Leave loose at this time.

SEE FIGURES 25-27

8 of 16

FIGURE 23 - STEP 21

FIGURE 25 - STEP 24

FIGURE 26 - STEP 24

FIGURE 28 - STEP 25

FIGURE 24 - STEP 23

FIGURE 27 - STEP 24

18MM BOLT

1/2” X 4” BOLT

Summary of Contents for FT22179i

















Search results

Summary of Contents for FT22179i

Reviews:

Related manuals for FT22179i

Brands by name

Popular brands

Fabtech FT22179i, Installation Instructions Manual

Search results

Summary of Contents for FT22179i

Reviews:

Related manuals for FT22179i

Brands by name

Popular brands