background image

Specifi cation

F860TX

F1150TX

F1600TX

F2000TX

8Ω Stereo Power (RMS)

450W X 2

760W X 2

1030W X 2

1300W X 2

4Ω Stereo Power (RMS)

860W X 2

1150W X 2

1600W X 2

2000W X 2

2Ω Stereo Power (RMS)

1150W X 2

1550W X 2

2200W X 2

3000W X 2

8Ω Bridged Power (RMS)

1360W

2400W

3300W

3300W

4Ω Bridged Power (RMS)

1460W

3200W

4500W

4600W

Frequency Response

20Hz–20kHz (+0/-2dB)

THD into 4Ω, 1KHz

<0.1%

<0.1%

<0.1%

<0.1%

IMD-SMPTE 

60Hz, 7kHz

<0.1%

<0.1%

<0.1%

<0.1%

Slew Rate

40Vµs

42Vµs

50Vµs

60Vµs

Damping Factor

at 100Hz/1kHz @ 8Ω

>400

>450

>450

>500

Voltage Gain

66V

80V

100V

123V

Input Sensitivity 

Full rated power @ 8Ω

1.4V

1.4V

1.4V

1.4V

Input Impedance

20kΩ/ Balanced, 10kΩ Unbalanced

Signal to Noise 

106dB

106dB

106dB

106dB

Crosstalk

<-80dB

<-80dB

<-80dB

<-80dB

Connectors 

Per

 

Channel

One male XLR . One Female XLR. 

One Speakon

TM

/ NL4

Power Supply

AC 110-220V/ 50-60Hz

Max. Current Draw 120V

(1Khz @ full power, 2Ω)

14.7V

15V

16.2V

17V

Cooling

Two (2) variable speed DC fans

Controls

Two (2) front panel attenuators.

Indicators

Per Channel

Power LED, -10dB LED, -30dB LED, Clip LED, Fault LED

Protection

Temperature, DC, Sub/Ultra sonic, Short Circuit, IGM, Output.

Dimensions

(H X W X D)

3.5” X 19” X 18.125”

Net Weight

32 lb

37 lb

45 lb

53 lb

Shipping Weight

39 lb

44 lb

51 lb

59 lb

 

 

 

 

Specifi cations

Note: Face Audio® is continually researching and developing, for this reason 

specifi cations may change without notice.

13

Summary of Contents for F1150TX





















Reviews: