17
c)
Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source
and/or battery pack,
picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing
power tools that have the switch on invites accidents.
d)
Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e)
Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in
unexpected situations.
f)
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving
parts.
Loose clothes, jewelry or long hair can be caught in moving parts.
g)
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected
and properly used.
Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a)
Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the
job better and safer at the rate for which it was designed.
b)
Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c)
Disconnect the plug from the power source and/or the battery pack from the power tool before making
any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d)
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e)
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other
condition that may affect the power tool’s operation. If damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained power tools.
f)
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to bind
and are easier to control.
g)
Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the
working conditions and the work to be performed.
Use of the power tool for operations different from those intended could
result in a hazardous situation.
5) Battery tool use and care
a)
Recharge only with the charger specified by the manufacturer.
A charger that is suitable for one type of battery
pack may create a risk of fire when used with another battery pack.
b)
Use power tools only with specifically designated battery packs.
Use of any other battery packs may create a risk
of injury and fire.
c)
When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails,
screws, or other small metal objects that can make a connection from one terminal to another.
Shorting the
battery terminals together may cause burns or a fire.
d)
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.
6) Service
a)
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will
ensure that the safety of the power tool is maintained.
Safety Rules for Drill/Drivers
• Wear ear protectors with impact drills
.
Exposure to noise can cause hearing loss.
•
Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
•
Hold power tool by insulated gripping surfaces when performing an operation where the fastener may contact
hidden wiring.
Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the
operator an electric shock.
•
Use clamps or other practical way to secure and support the workpiece to a stable platform.
Holding the work
by hand or against your body is unstable and may lead to loss of control.
Summary of Contents for CL3.P18S
