background image

                                                                                                 

 

11 

www.factorelectronics.com 

HD100BaseT-Balun User Manual 

Factor Electronics 

Maintenance 

Clean this unit with  a soft, dry cloth.  Never use  alcohol, paint thinner or benzene to clean this  

unit. 

 

Warranty Policy 

Factor Electronics products are warranted against defects in material and workmanship for two 

years  from  the  date  of  shipment.  During  the  warranty  period,  Factor  Electronics  will,  at  its 

option,  repair  or  replace  products  that  prove  to  be  defective.  Repairs  are  warranted  for  the 

remainder  of  the original  warranty  or  a 90  day extended  warranty,  whichever  is longer.   

For equipment under warranty, the owner is responsible for freight to  Factor Electronics and all 

related  customs,  taxes,  tariffs,  insuranc e,  etc.  Factor  Electronics  is  responsible  for  the  freight  
charges  only  for  return  of  the  equipment  from  the  factory  to  the  owner.  Factor  Electronics  will 

return  the  equipment  by  the  same  method  (i.e.,  Air,  Express,  Surface)  as  the  equipment  was  

sent to Factor Electronics.   

All  equipment  returned  for  warranty  repair  must  have  a  valid  RMA  number  issued  prior  to 

return  and  be  marked  clearly  on  the  return  packaging.  Factor  Electronics  strongly  

recommends  all equipment  be returned  in its original  packaging.       

Factor  Electronics

s  obligations  under  this  warranty  are  limited  to  repair  or  replacement  of 

failed  parts, and  the return  shipment  to the buyer  of  the  repaired  or  replaced  parts.  

 

Limitations  of Warranty 

The warranty does not apply to any part of a product that has been installed,  altered, repaired,  

or  misused  in  any  way  that,  in  the  opinion  of  Factor  Electronics,  would  affect  the  reliability  or 

detracts from the performance of any part of the product, or is damaged as the  result of use in 
a way  or with  equipment  that had not  been  previously  approved  by Factor  Electronics.   

The  warranty  does  not  apply  to  any  product  or  parts  thereof  where  the  serial  number  or  the 

serial  number  of any  of its parts  has been  altered,  defaced,  or  removed.   

The  warranty  does not cover  damage  or loss incurred  in transportation  of  the product.   

The  warranty  does  not  cover  replacement  or  repair  necessitated  by  loss  or  damage  from  any  

cause beyond the control  of Factor Electronics, such as lightning or other natural and weather 
related  events  or wartime  environments.   

The  warranty  does  not  cover  any  labor  involved  in  the  removal  and  or  reinstallation  of 

warranted equipment or parts on site, or any labor required to diagnose the nec essity for repair 
or  replacement.   

Summary of Contents for HD100BaseT-Balun TX














Reviews: