background image

jumping, downhill and/or training for any such events or as a result of exposing the bicycle to, or riding 
the bicycle in, severe conditions or climates.

Labour and/or transport charges for full or part replacement, repair, return or changeover.

Accident, neglect, improper handling, abuse or wilful damage, misuse, improper assembly and use of 
devices or components not originally intended for, or not compatible with the bicycle.

Any alteration or repair by you or a third party who is not one of our authorised repairers.

Any specification provided by you. Remedy: Unless otherwise provided, the sole remedy under the 
above Factor warranty, or any implied warranty, is limited to repair or replacement of defective parts 
with those of equal or greater value at the sole discretion of Factor.

Except for this remedy Factor will not be responsible for any direct, incidental or consequential loss or 
damages, including, without limitation, loss or damages for personal injury, property damage or 
economic losses, whether based on contract, warranty, negligence, product liability or any other 
theory.

Nothing in this limited warranty will exclude or limit Factor’s liability for death or personal injury 
caused by Factor’s negligence or any other liability which cannot be excluded or limited by law. Unless 
you are a consumer, Factor makes no other warranties, express or implied and all implied warranties, 
including warranties of merchantability, reasonable care, and fitness for a particular purpose are 
hereby disclaimed.

Miscellaneous:

In the event that Factor prevails in any court action, you agree to reimburse Factor for the expenses, 
including attorney’s fees and expenses of litigation incurred by Factor in defending against your claim.

Claims made outside the country of purchase may be subject to additional fees and restrictions.

Warranty detail and duration may differ by country. This warranty gives you specific legal rights, and 
you may also have other rights which may vary from place to place. This warranty does not affect your 
statutory rights.

To the extent that this warranty statement is inconsistent with local law, this warranty shall be 
deemed modified to be consistent with such law; under such law, certain disclaimers and limitations 
may apply to the customer.

Some states and countries do not allow the exclusion or limitation of incidental or consequential 
damages or warranties, so the above limitations or exclusions may not apply to you.

If it is determined by a court of competent jurisdiction that a certain provision of this limited warranty 
does not apply, such determination shall not affect any other provision of this limited warranty, and all 
other provisions shall remain in effect.

The English language version of this limited warranty will prevail.

This limited warranty is governed by the laws of  European Union and United States  and the courts 
of European Union and United States  shall have the non-exclusive jurisdiction to settle any dispute 
or claim arising out of or in connection to this limited warranty or its subject matter or formation 
(including non-contractual disputes or claims).

Assembly Manual

 

Summary of Contents for SLiCK



















Reviews: