6
The 4th motor speed level is the intensive function and is
timer-operated.
The standard period of time is 5’, at the end of which the
hood reverts to speed level 2.
To deactivate the function before the set time has elapsed,
simply press the “-” button.
SPECIAL FUNCTIONS
Programming the Clock
The clock may be set at any time, apart from when the
timer function is active.
The clock may be displayed in a 12-hour format, indicating a
time between 1:00 and 12:59.
The clock may be reset by pressing and holding the
“Timer” button for 5 seconds, then pressing the “-” and
“+” buttons to adjust the time.
The user may increase/decrease the time in steps of 1
minute; however, if the “-” or “+” button is pressed for 1
second, the time is decreased/increased in steps of 5
minutes. In this case, the control panel rounds the time
off to the nearest 5 minutes.
The user can end the clock resetting stage by pressing
the “Timer” button.
If none of the buttons are pressed for 1 minute, the control
panel accepts the set value and adds on 1 minute, then
begins to operate normally.
Grease filter warning
After
40
hours of operation, “Grease Filter” appears on the
display. When this text appears, the filter needs to be washed.
To reset the grease filter warning, the user should press
and hold the “+” button for 5 seconds. After this action,
the “Grease Filter” text will disappear, a “beep” will be
emitted to indicate the process is compete and the
display will return to showing its normal operating
functions.
The grease filter counter will reset after this procedure is
complete.
Charcoal filter warning
After
160
hours of operation, “Charcoal Filter” appears on the
display. When this text appears, the filter needs to be
replaced.
To reset the charcoal filter warning, the user should press
and hold the “-” button for 5 seconds. After this action,
the “Charcoal Filter” text will disappear, a “beep” will be
emitted to indicate the process is compete and the
display will return to showing its normal operating
functions.
The charcoal filter counter will reset after this procedure is
complete.
Enabling/disabling the charcoal filter warning
The charcoal filter may be enabled or disabled by
pressing and holding the “-” and “+” buttons
simultaneously for 5 seconds. The inclusion or exclusion
of the charcoal filter must be selected while the motor
and light are OFF.
Charcoal filter excluded: the filter alarm is disabled.
Enabling/disabling the sound signal
The sound signals may be activated or deactivated by
pressing and holding the "Light" button for 5 seconds.
If the sound signal has been activated, it should emit a
beep and the text “Snd” should appear on the display for
2 seconds.
If the sound signal has been deactivated, the text “Snd”
should appear on the display for 2 seconds and no beep
should be emitted.
Temperature alarm
The hood is fitted with a temperature sensor which
activates the motor at speed level 2 in the event that the
temperature in the display area exceeds 70°C (the
system monitors the data recorded by the sensor every
250 ms).
If the motor is OFF or at speed level 1 and the alarm
intervenes, the motor will move to speed level 2 and the
text “care” will appear on the display. While the
appliance is in its alarm operating status, the user may
only increase the motor speed (3rd and 4th levels). When
the temperature of the cooker hood returns to a level
below the alarm threshold, the motor will return to the
status which was set before the alarm condition occurred.
3 minutes after the intervention of the alarm, the system
will check the temperature in the display area again: if it
is lower than 70°C, the operating conditions set prior to
the intervention will be restored.
Maintenance
ATTENTION!
Before performing any maintenance operation,
isolate the hood from the electrical supply by switching off at
the connector and removing the connector fuse.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products.
DO NOT USE ALCOHOL!
Warning:
Failure to carry out the basic cleaning recommendations of the
cooker hood and replacement of the filters may cause fire
risks.
Therefore, we recommend oserving these instructions.
The manufacturer declines all responsibility for any damage to
the motor or any fire damage linked to inappropriate
maintenance or failure to observe the above safety
recommendations.
