10
attempt to repair. If a repair is required,
contact a Technical Assistance Service
authorised by the manufacturer and
request the use of original spare parts.
•
If the cable for this appliance is
damaged, contact an authorised
Technical Assistance Service for it to be
replaced.
•
Do not leave the appliance exposed to
the elements (rain, sun, ice, etc.).
•
Do not use or let any part of the
appliance come into contact or near hot
surfaces (kitchen gas or electric hobs or
ovens).
•
Do not use detergents or abrasive
sponges to clean the appliance.
•
Do not touch the hot surfaces. Use the
handles.
•
Do not let the cable come into contact
with the hot parts of the appliance.
•
The blade is very sharp. Handle it
carefully to avoid cuts.
•
Do not fill the blender any higher than
the maximum level (1500 ml).
•
Do not remove the jug from the motor
base when the appliance is functioning.
•
Ensure the jug lid is properly fitted
before using the blender.
•
Do not place your hands or any
objects in the jug when the blender is
functioning. If necessary, disconnect the
appliance and use a spatula to remove
any food stuck to the walls of the jug.
•
Do not submerge the motor base in
water or any other liquid.
•
Do not touch the rotating parts while
they are in movement. Always wait for
them to stop.
•
This appliance must only be used for
processing food.
•
This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
•
Children should be supervised to ensure
that they do not play with the appliance
•
When mixing hot liquids/foods excess
pressure may build up inside the
4. OPERATING INSTRUCTIONS
Before using the blender for the first time,
clean the dispenser cap, jug lid, jug and
blade in warm soapy water and dry them
thoroughly before assembling them again.
ASSEMBLY
Unplug the appliance before carrying out
any dismantling or assembly operations.
1.
Place the rubber seal
(4)
on the edge of
the blade unit
(5) (Fig. B).
2.
Insert the blade unit
(5)
in the joint
(6)
(Fig. C).
3.
Screw the bottom part of the glass jug
(3)
onto the joint
(6)
and turn it anti-
clockwise
(Fig. D)
.
4.
Fit the jug onto the motor base
(7)
,
aligning the jug with the grooves on
the motor base
(7)
, and then turn it
clockwise
(Fig. E)
5.
Firmly close the lid
(2) (Fig. F)
.
6.
Place the dispensing cap
(1)
in the hole
in the lid and turn it anti-clockwise
(Fig.
G)
.
To dismantle the blender, to clean it for
example, carry out the assembly process in
reverse order.
ADJUSTMENT
•
Place the assembled blender on a flat,
stable surface.
•
Before plugging in the blender, make
sure the jug is correctly fitted and in
place on the motor base
(7)
.
NOTE:
The blender has a safety lock
system to ensure the appliance can only
blender and this could make the lid
come off and the contents splash out.
We therefore recommend that you avoid
mixing excessively hot foods and that
you only put very small quantities of hot
liquids or foods into the blender.
•
Do not use the blender for very hard
food products, such as bones, shelled
nuts, frozen meats etc., which could
either damage the blade or cause the
motor to seize.
•
CAUTION:
Do not use the unit
continuously more than 2 minutes.
Summary of Contents for BV-1000X
