Probing (·T· model).
CNCelite
8058 8060
8065
4.
CANNED CYCLES. CYCLE EDITOR.
How to
d
efine the da
ta of th
e editor.
ꞏ64ꞏ
R
EF
. 2106
4.1
How to define the data of the editor.
To enter or modify a data, it must be selected; i.e. it must have the editing focus on it. The
parameters of the cycles may be selected with the [
] [
] [
] or [
] keys, or with the direct
access keys. The first data of each group may also be selected by pressing the page-up and
page-down keys.
The direct access keys correspond to the name of the parameters; [F] for forward
movements, [T] for tools, etc. Each time the same key is pressed, the next value of the same
type is selected.
Manual data entry.
• To modify a numerical data, key in the desired value or press [DEL] to leave the data
undefined. In either case, press [ENTER] for the cycle to assume the new value.
• Press the [SPACE] key to change the status of this icon.
Leaving some data undefined.
Some data may be left undefined (empty checkbox). In this case, the cycle behaves as
follows.
• If the cycle position is not defined, it is executed at the current position the axes when
calling the cycle.
• If the tool number is not defined, it will be executed with the tool that is active at the time
of execution.
Defining data using arithmetic parameters..
Numerical data may be defined using global arithmetic parameters (P100-P9999) or
common ones (P10000-P19999). In this case, when executing the cycle, these data will
assume the value that the parameter has at the time.
When using global parameters, bear in mind that some cycles modify the value of these
parameters at the end of the execution. Refer to each cycle to see which parameters it
modifies.
Teach-in mode for data entry.
The Teach-in mode may be used to jog the axes and assign their current position to the data
that define the position of the cycle. The axes may be jogged using the jog keypad, the
handwheels or via MDI.
To assign a value to a data, select it with the cursor (focus on it) and press the [RECALL]
key. The data is taken from the channel where the editing-simulation mode is active.
• The X axis related data takes the coordinate of the first axis of the channel.
• The Z axis related data takes the coordinate of the second axis of the channel, if the
channel has only two axes. If there are three or more axes, the data takes the coordinate
of the first axis of the channel.
The Teach-in mode is activated from the horizontal softkey menu. When
the Teach-in mode is active, the bottom of the screen shows a window with
the axes of the channel.
Summary of Contents for CNC 8058elite T
