Fagor CNC 8070 Hardware Configuration Download

Page: 96 / 276

Hardware configuration.

CNC 8070

CEN

RAL UNIT + MONITOR (Q7-A

PLATFORM).

ific

·96·

: 1911)

The machine manufacturer must comply with the EN 60204-1 (IEC-204-1) regulation
regarding electrical shocks in case of defective input/output pins with external power supply
when not plugging the connector before turning the power supply on.

Ambient.

• Storage and transport temperature:

- Between -40 ºC (-40 ºF) and +70 ºC (158 ºF).

• Work temperature:

- Between 5 ºC (41 ºF) and 55 ºC (131 ºF).

• Temperature outside cabinet:

- Between 5 ºC (41 ºF) and 45 ºC (113 ºF).

• Temperature inside the enclosure:

- Less than 55 ºC (131 ºF).

• Relative humidity:

- 20 ~ 85% RH without condensation.

• Pollution degree 2.
• Maximum work altitude:

- The unit must work properly at 2000 m according to IEC 61131-2.

• Vibration test according to IEC 60068-2-6 with a frequency step of 1

octave/minute (±10%) and a duration of 10 sweeps.
- 5 Hz



8.4 Hz; movement of constant 3.5 mm amplitude (peak value).

- 8.4 Hz



150 Hz; 1g acceleration and constant amplitude (peak value).

• Degree of protection:

- IP65 (front), IP20 (rear).

Power supply.

• Use a regulated 24 V DC power supply (between -15% and +20%) and 2 A

(including voltage ripple and noise). The power supply must meet the
UL1950 standard.

Connectivity.

• 3 USB 2.0 ports, (one accessible at the front, protected by a cover).
• 1 USB 3.0 port
• 1 RS-232/422/485 (115 kbps) serial port (optional).
• 1 Ethernet port for 10/100/1000 BaseT connection.
• CAN Bus (CANfagor/CANopen).
• Sercos II bus.
• EtherCAT bus.

Inputs/outputs.

• 16 opto-coupled digital inputs (24 V DC).

- IEC61131-2 type 1 and type 3 compliant.

• 8 opto-coupled digital outputs (24 V DC, 500 mA).

- ON cycle: minimum 75 µs (25 µs, optional in two of them).

• 1 analog outputs (±10 V, 16-bit resolution).
• 1 feedback inputs (5 V, 250 mA).

- Incremental TTL signal, differential TTL or 1 Vpp.
- Frequency : 100 kHz (TTL), 1000 kHz (TTL differential) / 500 kHz (1 Vpp).

• 1 relay with one normally open contact (1A at 24V).
• 2 probe inputs (5 V or 24 V)
• 1 entry for UPS unit control.
• 1 input for three handwheels with A and B signals (5 V DC TTL)

(only C70-10K).

Type.

Description.

To help increase storage space, Fagor Automation lists several CFast cards in its catalog; when using
a third-party CFast, always use an industrial grade CFast SLC as these support temperatures from
between -40ºC and +85ºC (-40 ºF and 185 ºF) and can last five years with constant day-to-day writing.
Fagor Automation shall not be held responsible for any problems caused by using lower-quality CFast
cards.

Do not run part programs from a USB port, whether it be while using a pendrive or external hard drive.
Fagor Automation recommends using the USB port only to exchanging data, such for programs,
reports, etc. If you require more storage space, then use a CFast disk.

DO NOT connect any kind of hub to the USB port.