CNC8070
R
EF
. 0402
OF
128
E
RROR
SOLUTIONS
Page 88 of 128
Errors 3000-3999
3036
'Wrong gear change process'
DETECTION
During execution.
CAUSE
The spindle gear in the CNC's history and the one indicated by the PLC as being
active are not the same.
SOLUTION
Check the PLC program.
3037
'Axis locked'
DETECTION
During execution.
CAUSE
The axis tries to move, but the SERVO is not ON.
SOLUTION
Check the treatment of the SERVO signal in the PLC program or increase the value
of the DWELL parameter of the axis.
3038
'Too many parameters pending to be reported'
DETECTION
During execution.
CAUSE
The system is overloaded.
SOLUTION
Close the Windows applications not related to the CNC. Contact Fagor.
3039
'The stop block has not been found in the block search'
DETECTION
While executing in dry run.
CAUSE
When executing the program in dry run, it does not go through the stop block.
SOLUTION
Change the stop block.
3040
'Hirth axis positioned wrong'
DETECTION
During execution.
CAUSE
The Hirth axis is not positioned in a multiple number of its step.
SOLUTION
Position the Hirth axis properly in a valid position or cancel it as Hirth axis.
3041
'No spindle has been defined for G33/G95'
DETECTION
During execution.
CAUSE
Functions G33 and G95 need a spindle to work. This spindle is by default the master
spindle of the channel, but if PLC register SYNC indicates another spindle, it works
with the latter.
If at a particular moment, none of the two is defined, an error is issued.
SOLUTION
Assign a spindle to the PLC register or have a master spindle defined in the channel.
3043
'Spindle in M5 when activating electronic threading'
DETECTION
During execution.
CAUSE
The spindle involved in electronic threading (G33) is in M5 by default, or an M5 has
been programmed in the same block as the G33.
SOLUTION
Program a spindle rotation first or in the same block as the G33 indicating the turning
direction (M3/M4) or the speed (S).
3500
'Linear acceleration of section 1 smaller than or equal to zero'
DETECTION
On startup or during execution.
CAUSE
A zero acceleration has been programmed.
SOLUTION
Program a positive value for the acceleration.
3501
'Linear acceleration of section 1 greater than the maximum'
DETECTION
During startup or execution.
CAUSE
An acceleration greater than the maximum has been programmed.
SOLUTION
Program a smaller value than the maximum for the acceleration.
3502
'Linear acceleration of section 2 smaller than or equal to zero'
DETECTION
On startup or during execution.
CAUSE
A zero acceleration has been programmed.
SOLUTION
Program a positive value for the acceleration.
3503
'Linear acceleration of section 2 greater than the maximum'
DETECTION
During startup or execution.
CAUSE
An acceleration greater than the maximum has been programmed.
SOLUTION
Program a smaller value than the maximum for the acceleration.
Summary of Contents for CNC8 070
