background image

 

Routine maintenance 

Have  the  condition  and  efficiency  of  the  gas  pipe  and  the  pressure  regulator  (if 
installed)  checked  periodically.  If  anomalies  are  found,  do  not  repairs  but  have  the 
faulty part replaced. 
 
To  ensure  good  performance  and  safety,  the  gas  regulator  taps  must  be  greased 
periodically. 
              Periodic  lubrication  of  the  taps  must  only  be  carried  out  by  qualified 

personel

, who must also be contacted if the appliance malfunctions. 

 

Service and parts 

Before leaving the factory, this appliance was tested and adjusted by specialist skilled 
staff  to  give  the  best  operating  results.  Any  subsequent  necessary  repairs  or 
adjustments must be carried out with the greatest care and attention. 
For this reason, we strongly advise you always to contact the Dealer who sold you the 
appliance  or  our  nearest  Service  Centre,  specifying  the  nature  of  the  problem,  the 
model  of  the  equipment  (Mod.)

,

  the  product  number  (Prod.  No.)  and  the  serial 

number(Ser.  No.).  These  data  are  provided  in  the  plate  on  the  cover  of  this  manual. 
Always request the use of original spare parts. 
 
 

Warranty conditions 

You new appliance is covered by a warranty. The warranty conditions are provided in 
full  in  the  “Warranty  conditions-Service  centers”  leaflet  which  you  will  find  inside 
the appliance 
Keep the fiscal receipt or delivery note, either of which documents  your purchase of 
the appliance and provides proof of date of purchase, in a safe place together with the 
leaflet. 
If  the  After-Sales  Service  is  call  in,  show  these  documents  to  the  staff.  If  this 
procedure  is  not  followed,  the  Service-Centre  will  have  no  option  but  to  charge  for 
any repairs. 
If  necessary,  you  may  find  your  nearest  Centre  by  consulting  the”  Warranty 
conditions –Service centers”.       
 
 

7   

 

Summary of Contents for Hob















Reviews: