Fagor QC-PDS Hardware Manual Download | Manualshive

Page: 15 / 420

background image

Ref.2003

· 15 ·

  

Previous I

QC-PDS

HARDWARE

Shipment

When shipping the unit, do it protected against blows and pack it in its original cardboard box with its
original packing material. If you do not have the original packaging material, pack it as follows:

1.

Get a cardboard box whose 3 inside dimensions are at least 15 cm (5.9 inches) larger than those of
the unit itself. The cardboard used to make the box must have a resistance of 170 kg (374.8 lb).

2.

Attach a label indicating the owner of the unit, person to contact, type of unit and serial number.

3.

In case of failure, also indicate the symptom and a short description of the failure.

4.

Protect the unit wrapping it up with a roll of polyethylene or with similar material.

5.

Pad the unit inside the cardboard box with polyurethane foam on all sides.

6.

Seal the cardboard box with packaging tape or with industrial staples.

Storage

Store the product only under the allowed ambient conditions indicated here. Refer to this data in chapter
1, section

1.6 AMBIENT AND OPERATING CONDITIONS

of this manual. Always protect the product against

dust and dirtiness.

Decommissioning and eliminating

The machine manufacturer must indicate the procedure for shutting down the machine.

Respect environmental regulations. Keep in mind that no QC-PDS servo units of the

Q

UER

C

US system

comes with a battery.

Bear in mind the storage and shipping requirements when getting rid of QC-PDS units.

Recycling. The product is made of various materials that may be recycled and eliminated separately.
Get rid of the product in compliance with local regulations.

SHIPPING CONDITIONS, STORAGE,

DECOMMISSION AND DISPOSAL

«
...
13
14
15
16
17
...
»

Summary of Contents for QC-PDS





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for QC-PDS

Brand: Parker Pages: 103

E MOTION Series

Brand: Saci Pages: 116

Brand: Beckhoff Pages: 208

Brand: Masterflex Pages: 20

Brand: Tecmar Technologies Pages: 46

Brand: Iomega Pages: 16

Brand: LinMot Pages: 27

Brand: Applied Motion Products Pages: 2

ThinkPad Multi-Burner Ultrabay Slim Drive

Brand: IBM Pages: 56

Brand: Danaher Motion Pages: 72

Brand: OE Max Controls Pages: 284

Brand: Xinje Pages: 23

Brand: Danfoss Pages: 77

Brand: Danfoss Pages: 144

Brand: Vathauer Pages: 25

Brand: JVC Pages: 24

Brand: JVC Pages: 112

Brand: JVC Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands