manualshive.com logo in svg

Fagor QC-PDS, Hardware Manual

The Fagor QC-PDS is a high-performance pressure cooker with a sleek design and easy-to-use features. Make sure to refer to the Original Instructions Manual for proper use and maintenance. You can download the manual for free from 88.208.23.73:8080 to ensure you get the most out of your cooking experience.

Share
Download
background image

  

Auxiliary modules

4.

AUXILIARY MODULES

Cap

acitor Mo

dul

e

174

Ref.2003

· 150 ·

QC-PDS

HARDWARE

4.5

Capacitor Module

Available models:

QC-CM-75

The QC-CM-75 commercial model is used to store energy that is returned
during the electric motor braking processes. 
The are also appropriate for systems that sporadically demand high
current peaks from the power DC BUS, which in turn increases the
capacity of the DC BUS.
From the energy point of view, installing a capacitor module is more
efficient than installing external braking resistors.

4.5.1

Outside appearance

Refer to the diagram for an overall view of the outside of the unit.

4.5.2

Technical data

size

width

references

1

78 mm

QC-CM-75

F. H4/7

QC-CM-75. Outside appearance.

A17.

Under cover 
(+/-) DC BUS terminals

Characteristics 
plate

Version/model 
label

M5x8 screws.
Connection for the 
Protective Earth wire

 PE

 

Tightening torque: 
3 N·m

Access lid for DC BUS with
bottom pivot hinge. Opening
and closing click tool

T. H4/11

QC-CM-75. Technical data.

CAPACITOR MODULE

QC-CM-75

Capacity

7.38 mF

Maximum voltage at the bus

797 V DC

Operating ambient temperature

0°C/45°C (32°F/113°F)

Storage temperature

-25°C/60°C (-13°F/140°F)

Relative humidity

< 90 % (non condensing at 45°C/113°F)

Operating vibration

1 g

Shipping vibration

1.5 g

Sealing degree

Open IP xx *

Size

1

Width in mm/in

78/3.1

Approx. mass in kg/lb

6.3/13.9

* 

Open IP xx

, to be installed inside a cabinet or assembly that provides the

required access protection.

Summary of Contents for QC-PDS





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for QC-PDS

IBM 22P6975 User Manual preview
22P6975
Brand: IBM Pages: 54
Allen-Bradley Kinetix 5100 2198-E1004-ERS User Manual preview
Kinetix 5100 2198-E1004-ERS
Brand: Allen-Bradley Pages: 500
WEG SCA06 User Manual preview
SCA06
Brand: WEG Pages: 79
FujiFilm GYN101CAG-G09 User Manual preview
GYN101CAG-G09
Brand: FujiFilm Pages: 252
Sanyo CRD-BPDV2 Owner'S Manual preview
CRD-BPDV2
Brand: Sanyo Pages: 30
Wheatstone iK series User Manual preview
iK series
Brand: Wheatstone Pages: 207
SOMFY J4 WT Summary Instruction preview
J4 WT
Brand: SOMFY Pages: 2
SOMFY Dexxo Compact RTS Installation Instructions Manual preview
Dexxo Compact RTS
Brand: SOMFY Pages: 10
SOMFY Irismo 35 Manual preview
Irismo 35
Brand: SOMFY Pages: 78
Parker IM20 Series Product Manual preview
IM20 Series
Brand: Parker Pages: 74
Parker OEM750 User Manual preview
OEM750
Brand: Parker Pages: 96
VLT AQUA Drive FC 200 Instruction Manual preview
AQUA Drive FC 200
Brand: VLT Pages: 96
Seagate Technology CTT 8000 Installation Manual preview
CTT 8000
Brand: Seagate Technology Pages: 22
D+H ZA 35 Original Instructions Manual preview
ZA 35
Brand: D+H Pages: 16
Küenle KFUtronic Series Instruction Manual preview
KFUtronic Series
Brand: Küenle Pages: 74
Stanley SCH20 User Manual preview
SCH20
Brand: Stanley Pages: 52
Acoms AS17 Technical Note preview
AS17
Brand: Acoms Pages: 4
LaCie Portable DVD RW Quick Install Manual preview
Portable DVD RW
Brand: LaCie Pages: 8

Brands by name

Popular brands

Load more brands