manualshive.com logo in svg

Fagor QC-PDS, Hardware Manual

The Fagor QC-PDS is a high-performance pressure cooker with a sleek design and easy-to-use features. Make sure to refer to the Original Instructions Manual for proper use and maintenance. You can download the manual for free from 88.208.23.73:8080 to ensure you get the most out of your cooking experience.

Share
Download
background image

  

Installation

8.

INSTAL

LAT

ION

Ele

ctrica

l co

nne

ctio

ns

302

Ref.2003

· 264 ·

QC-PDS

HARDWARE

For single-drives, size|9

The power connection for a spindle motor to a QC-DR-275-



, size|9

single-drive is made using a single-pole MPC-1x150 cable via the threaded
bolts U1/U, V1/V and W1/W found on the upper side of the of the drive. The
connection between the chassis and the protective earth (PE) is made via
the M8 screw of the protective earth (PE) also found on the upper part of
the drive. The shield of the single-pole MPC-1x150 power cable is
connected to the protective earth at both cable ends. On the drive side via
the chassis support provided with the drive. Next, the chassis is connected
to the protective earth (PE) via its M8 screw. 

Be sure to strip the power cable to expose the shield at both ends. Use a
metal clamp complete this connection to the chassis support on the drive
side. 

See figures.

F. H8/21

Power connection threaded bolts of the spindle motor to the single-drive,
size|9.

F. H8/22

Power connection of the spindle motor to the single-drive, size|9.

M10

M10

M10

QC-DR-275-



 

TALLA|9

U1/U-V1/V-W1/W
QC-DR-275-



250 A

U1/U-V1/V-W1/W

PE

M

3

U 1 / U  

U
V

W

M O T O R   F M 9 - A 1 3 0

Q C - D R - 2 7 5 - X X

V 1 / V  

W 1 / W  

1

1

1

M P C - 1 x 1 5 0

s i n g l e - p o l e   c a b l e   p e r   p h a s e  

w i t h o u t   t e r m i n a l s

S

³

7 0   m m

2

S

³

7 0   m m

2

P E

P E

s h i e l d s   t o   t h e   p r o t e c t i v e   e a r t h

i n   t h e   c h a s s i s   s u p p o r t

A d d i t i o n a l l y ,   c o n n e c t   t h e   c h a s s i s   s u p p o r t   t o   t h e   p r o t e c t i v e   e a r t h  

p r o t e c t i v e   e a r t h   s c r e w   o f   t h e  

m o t o r   t e r m i n a l   b o x

p r o t e c t i v e   e a r t h   s c r e w  

o f   t h e   d r i v e

Summary of Contents for QC-PDS





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for QC-PDS

Danfoss VLT AutomationDrive FC 301 Operating Instructions Manual preview
VLT AutomationDrive FC 301
Brand: Danfoss Pages: 84
Sprint Electric Option CON113 Product Manual preview
Option CON113
Brand: Sprint Electric Pages: 8
Technodrive KR-A535M Manual preview
KR-A535M
Brand: Technodrive Pages: 1
Hubbell Dual Hose Reel-Direct Drive K-32 Installation And Maintenance Instructions preview
Dual Hose Reel-Direct Drive K-32
Brand: Hubbell Pages: 4
Uni-Pex P-600NT Instruction Manual preview
P-600NT
Brand: Uni-Pex Pages: 2
Raymarine SmartPilot X-10 Installation Manual preview
SmartPilot X-10
Brand: Raymarine Pages: 12
Fagor ACSD series Original Instructions Manual preview
ACSD series
Brand: Fagor Pages: 82
D+H CDP 1500 BSY+ Original Instructions Manual preview
CDP 1500 BSY+
Brand: D+H Pages: 28
Rockwell Automation Allen-Bradley PowerFlex 753 Manual preview
Allen-Bradley PowerFlex 753
Brand: Rockwell Automation Pages: 20
Rockwell Automation Allen-Bradley PowerFlex 700 B Series User Manual preview
Allen-Bradley PowerFlex 700 B Series
Brand: Rockwell Automation Pages: 228
Unitek Classic Q6 Manual preview
Classic Q6
Brand: Unitek Pages: 28
Panasonic MINAS A6N Series Manual preview
MINAS A6N Series
Brand: Panasonic Pages: 113
EasyDrive GT610 Series User Manual preview
GT610 Series
Brand: EasyDrive Pages: 137
Danfoss VLT 6002-6005 Installation, Operation And Maintenance Manual preview
VLT 6002-6005
Brand: Danfoss Pages: 118
Danfoss VLT DSD 510 Operating Manual preview
VLT DSD 510
Brand: Danfoss Pages: 226
LG GDR-8162B User Manual preview
GDR-8162B
Brand: LG Pages: 16
LG GDR-8162B Service Manual preview
GDR-8162B
Brand: LG Pages: 55
LG CED-8120B - - CD-RW Drive User Manual preview
CED-8120B - - CD-RW Drive
Brand: LG Pages: 22

Brands by name

Popular brands

Load more brands