Fagor QC-PDS Hardware Manual Download

Page: 78 / 420

  

Power supplies

POWER SUPPLIES

Rege

nerative

Pow

er Su

ppli

· 78 ·

Ref.2003

· 78 ·

QC-PDS

HARDWARE

The user must configure the QC-RPS-160-

N0 power supply with:

The minimum DC BUS voltage required to properly meet the features

required by the system (especially with the needs of the motors installed
and

A voltage setpoint no lower than 1.48 x Vline, approximately.

The possible configuration it offers are:

QC-RPS-160-

N0 power supplies will always work in the mode

configured by the switches: either RPS mode or RB6 mode.

RPS operating mode.

Increase to the VP5 voltage value.

The value of

the DC BUS voltage must be approximately that set by the user in
parameter VP5 of the QC-RPS power supply. By default, this value is
650 V DC.

MAX. 725 V DC

Select this configuration if

440 V AC



line



420 V AC

If it cannot properly meet the features required by the system, change the
value of VP5.

RPS operating mode.

Boost to 625 V DC.

The DC BUS voltage is

lower than 625V DC, approx.

Select this configuration if

420 V AC



line



400 V AC

. If the features

required by the system are not met, choose another switch configuration
to obtain a higher DC BUS voltage.

RPS operating mode.

Boost to 600 V DC.

The DC BUS voltage is lower

than 600 V DC, approx.
Select this configuration if

line



400 V AC

If the features required by the system are not met, choose another switch
configuration to obtain a higher DC BUS voltage.

RB6 operating mode.

Maintain 1.41xV

line

The voltage value of the

DC BUS will be the rectified value of the mains peak voltage.
Select this configuration if

line



440 V AC

. Note, however, that the RB6

operating mode can be configured for any line voltage. If it cannot
satisfactorily meet the features required by the system with this switch
configuration, choose another one.

Configurations

F. H2/30

Selection switches for the DC BUS voltage setpoint. Configurations.

1 2

RPS MODE

RB6 MODE

VP5 V DC

1 2

625 V DC

1 2

600 V DC

1 2

1.41 Vline



Represents the moving element of each switch.

INFORMATION

The QC-RPS-160-

N0 regenerative power supplies leave

the factory with the switches configured to option 2 (625 V DC).

IMPORTANT.

Make sure software version 01.01 or higher is installed on the power
supply.

Meaning

VP5 V DC

625 V DC

600 V DC

1.41 Vline

Summary of Contents for QC-PDS





































































































































































































































































































































































































































Search results

Summary of Contents for QC-PDS

Reviews:

Related manuals for QC-PDS

Brands by name

Popular brands

Fagor QC-PDS, Hardware Manual

Search results

Summary of Contents for QC-PDS

Reviews:

Related manuals for QC-PDS

Brands by name

Popular brands