manualshive.com logo in svg

Fagor QC-PDS, Hardware Manual

The Fagor QC-PDS is a high-performance pressure cooker with a sleek design and easy-to-use features. Make sure to refer to the Original Instructions Manual for proper use and maintenance. You can download the manual for free from 88.208.23.73:8080 to ensure you get the most out of your cooking experience.

Share
Download
background image

  

Selection criteria

S

E

LECT

ING CRI

T

ERIA

Cal

cu

lation

 for the inp

ut transformer powe

r an

d ca

ble

 sectio

n

5.

· 197 ·

Ref.2003

QC-PDS

HARDWARE

5.6

Calculation for the input transformer power and cable section

Calculation of the input transformer power for connection to the mains.

Calculation of the cable section for connection to the mains

T. H5/21

Input transformer/auto-transformer power.

T. H5/22

Selecting the power cable.

MAINS VOLTAGE

The QC-PDS system requires a line tension between 400 (1-10 %) V AC and 480 (1+10 %) V AC

TRANSFORMER

Transformer or auto-transformer power:

NOTE.

 

When using an isolating transformer, the secondary must have a star connection and its mid point must be

a c c e s s i b l e   s o   i t   c a n   b e   c o n n e c t e d   t o   g r o u n d .   T h i s   m e a n s   t h a t   t h e   o u t p u t   v o l t a g e   o f   t h e
transformer/autotransformer is maintained for the indicated apparent power. Note that if the system has an QC-
RPS-

-



 power supply, the rated power Pm of cell (2) of the previous expression corresponds to the sum of the

Pn's of all the asynchronous spindle motors of the system, whose value is the result of applying the expression
Pn=1.4·Pmax for each of them and then adding them all. Pmax will be the motor's maximum braking power and it
may be, in general, close to the power of the asynchronous spindle motor in S6. If it is a QC-PS-

 power supply,

cell (2) will register the value obtained from the tables 

T. H5/15

 or 

T. H5/16T. H5/17

, accordingly.

[

1

+

2

]

*

1.05 kVA

=

4

kVA

POWER CABLE FOR MAINS CONNECTION

Vline from 400 V AC to 480 V AC

Rated current through the mains cable conductor

MAINS POWER

QC-DR-X-XX DRIVE FOR FEED AXIS CONTROL:

QC-DR-X-XX DRIVE FOR SPINDLE CONTROL:

Power cable

Power cable

In Amperes

Reference

In Amperes

Reference

C 

 13.1

MPC-4x1.5

54.0 < C 

 70.0

MPC-4x25

13.1 < C 

 17.4

MPC-4x2.5

70.0 < C 

 86.0

MPC-4x35

17.4 <  C 

 23.0

MPC-4x4

86.0 < C 

 103.0

MPC-4x50

23.0 < C 

 

30.0

MPC-4x6

103.0 < C 

 130.0

MPC-1x70

30.0 < C 

 40.0

MPC-4x10

130.0 < C 

 156.0

MPC-1x95

40.0 < C 

 54.0

MPC-4x16

156.0 < C 

 179.0

MPC-1x120

179.0 < C 

 262.0

MPC-1x150

The purchase order must indicate the length of the cable.

4

(kW)

 

x 1000 / (

3 · Vmains)

=

A

C

Rated current on FKM motors

=

A

C

Maximum current on FM7|FM9 motors

=

A

C

Conductor section calculated for the B2 installation method, according to UNE-EN 60204-1:2007.

Summary of Contents for QC-PDS





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for QC-PDS

HPI Racing SF-50 Instructions preview
SF-50
Brand: HPI Racing Pages: 2
Lenze 8400 protec StateLine mit SO10 Manual preview
8400 protec StateLine mit SO10
Brand: Lenze Pages: 66
Saci E MOTION Series Installation And Maintenance Manual preview
E MOTION Series
Brand: Saci Pages: 116
SEW movigear sni-b Operating Instructions Manual preview
movigear sni-b
Brand: SEW Pages: 268
D+H KA 34-BSY+ Original Instructions Manual preview
KA 34-BSY+
Brand: D+H Pages: 20
Chrosziel Zoom Series User Manual Addendum preview
Zoom Series
Brand: Chrosziel Pages: 3
TECO T-Verter E2 Series Operating Manual preview
T-Verter E2 Series
Brand: TECO Pages: 64
G-U ELTRAL KS 30/40 Remote Assembly And Operating Instructions Manual preview
ELTRAL KS 30/40 Remote
Brand: G-U Pages: 16
G-U ELTRAL KS 30/40 RADIO CONTROL Installation And Operating Instructions Manual preview
ELTRAL KS 30/40 RADIO CONTROL
Brand: G-U Pages: 20
G-U ELTRAL S100 Assembly And Operating Instructions Manual preview
ELTRAL S100
Brand: G-U Pages: 24
Shihlin SS2 Series Installation Manual preview
SS2 Series
Brand: Shihlin Pages: 4
Parker FL20-CA Series Product Manual preview
FL20-CA Series
Brand: Parker Pages: 321
Parker FL20-S Series Manual preview
FL20-S Series
Brand: Parker Pages: 347
Stober CANopen SD6 Operating Manual preview
CANopen SD6
Brand: Stober Pages: 65
ROBEL ROPOWER 70.02 Operating Manual preview
ROPOWER 70.02
Brand: ROBEL Pages: 152
Eurotherm Drives 631 Product Manual preview
631
Brand: Eurotherm Drives Pages: 94
Eurotherm Drives 584S Product Manual preview
584S
Brand: Eurotherm Drives Pages: 176
Yolico YD3000N Series Instruction Manual preview
YD3000N Series
Brand: Yolico Pages: 139

Brands by name

Popular brands

Load more brands