background image

WaŜne

5/8

5/8

Cooperation of devices from different manufacturers in Z-Wave network

Z-Wave allows to integrate devices of different manufacturers which can work in different

groups; lighting, heating, domestic automation, etc. Z-Wave devices operate as repeaters in the

network, thus increasing the range of radio communication. The more devices in the network,

the more reliable and more resistant to interference is performance of the devices within the

network.

Adding device to the network operated by the controller of other manufacturer

Note! Make sure that the device (blackout blind) does not belong to any other network.

Start INCLUDE procedure with the controller of existing network and then press

“programming” button on the blackout blind being added to the network.

Note: Information how to initiate and perform INCLUDE and ASSOCIATE function with the use of

controllers of other manufacturers is to be found in the instructions of these devices.

Special function – ALL ON, ALL OFF

It is possible to define whether the blackout blind has to respect “close all” or “open all”

commands.

Note! Instructions how to define respecting functions “close all” and “open all” are to be found in

instructions of the respective devices.

Manual operating

The “manual operating button” allows operating the ARF Z-Wave blackout blind directly

after its installation. In order to control the blackout blind manually it is necessary to press

manual operating button. The buttons work sequentially e.g. start, stop, start in another direction,

stop, etc.

1 . Pressing the button for the first time starts the blackout blind to unfold.

2. Second pressing the button stops the blackout blind.

3. Third pressing the button starts the blackout blind in the opposite direction.

NOTE!

Before proceeding to programming check whether the device is not already assigned to

other network. It is indicated by network status LED diode. Network status light-emitting LED

diode informs that the device is not part of the network and can be added to any network. If the

device is powered and network status LED diode does not emit light, it is necessary to perform

EXCLUDE procedure.

Adding device to the network (controller) – INCLUDE function.

In order for the device to communicate within the Z-Wave network it is essential to

connect it to the network with the use of PRIMARY controller. The device can be added to the

network as long as it does not belong to any other network.

NOTE!

Information how to initiate and perform INCLUDE function is to be found in the

instructions of ZWP, ZWK and ZWG controllers offered by FAKRO.

Assigning device to operating buttons – ASSOCIATE function.

In case of some controllers after correct adding the device to the network it is necessary

to assign them to the specific group of operating buttons used for controlling the device. For this

purpose use ASSOCIATE function.

NOTE!

Information how to initiate and perform ASSOCIATE function is to be found in the

instructions of ZWP, ZWK and ZWG controllers offered by FAKRO.

Device programming / Additional information

Summary of Contents for ARF Z-Wave









Reviews: