background image

3

ó Attic ladder fully assembled and ready for installation.  You should not dismantle assembled product for installation

ó Control rod

Prior to installation inspect the product for any cracks in the wood.  Make sure that the metal elements are not damaged and securely

fastened.

III. REQUIRED MANPOWER, TOOLS AND MATERIALS

Manpower

ó 2 people (one must be able to lift 65 LB and carry it in to the attic)

Materials

ó few pieces of joist-sized lumber
ó 2 boards 1x4x36

Ē

 for temporary support

ó few boards for working platform in the attic space
ó wood shim stock
ó 20d sinker nails
ó 4

Ē

 screws for wood

Stepladder

Stepladder should be long enough to allow you to enter the overhead space.  Make sure that the ladder will withstand your 65 Lb.

WARNING

You should be extremely causious while climbing the ladder, other person should be holding the ladder preventing it from tipping over.

Tools

ó flashlight
ó claw hammer
ó pencil
ó hand saw
ó tape measure
ó framing square
ó power drill
ó 1/8

Ē

 drill bit

ó tools to cut opening in the ceiling

Safety equipment

ó gloves
ó safety goggles
ó dust mask

II. YOUR PACKAGE SHOULD CONTAIN:

Summary of Contents for LWS-P 22/47

















Reviews: