background image

 

13 

Harmonized standards 

 
This  product  complies  with  the  following 
standards: 
 
Safety:  EN61010-1 
EMC:   EN61326 
FCC:   47 CFR 15 
 

   

 

 
 

 

WEEE and RoHS 

 
Do not dispose of the WMA-100A amplifier 
as  standard  waste,  but  discard  it  at  a 
WEEE  electronic  waste  collection  point. 
The amplifier has been built in compliance 
with the RoHS directive. 
 
 

Warranty 

 
Falco  Systems  products  are  guaranteed 
against  malfunction  due  to  defects  in 
materials or workmanship for a period of 1 
year from the date on the invoice. 
If  a  malfunction  occurs  during  this  period, 
the  product  will  be  repaired  or  replaced 
without  charge.  The  product  will  be 
returned  to  the  customer  free  of  charge. 
The warranty does not apply to: 
- Exterior finish or appearance. 
- Malfunction of the product resulting from 
use  or  operation  in  other  ways  than 
specified in the user manual. 
- Malfunctioning due to misuse or abuse of 
the product. 
- Malfunctioning occurring after changes or 
repairs  have  been  made  by  anyone  other 
than Falco Systems. 
 
To  obtain  warranty  service,  inform  Falco 
Systems via 

info@falco-systems.com

  

You  will  receive  support  and  further 
instructions. 
 
 Falco  Systems  will  not  be  liable  for  any 
consequential damages, including, without 
limitation, devices or equipment connected 
to  the  product,  injury  to  persons  or 
property  or  loss  of  use.  For  more  details 
see  the  Falco  Systems  Standard  Terms 
and Conditions of Sale, which can also be 
downloaded on 

www.falco-systems.com

 

 

User manual version 

 
User manual version: 1.0 
Date: October 26, 2021 
 

Falco Systems 

 
Falco Systems BV 
Remisestraat 1   
2225 TH Katwijk aan Zee 
The Netherlands 
 
Phone:    +31 (0)6 21840996 

 

Email:     

info@falco-systems.com

  

Website: 

www.falco-systems.com

  

 

 

Summary of Contents for WMA-100A














Reviews: