background image

14

Cleaning your cooker

Before thorough cleaning, isolate from the 
electricity supply. Remember to switch on the 
electricity supply before use.

Never use paint solvents, washing soda, 
caustic cleaners, biological powders, bleach, 
chlorine based bleach cleaners, coarse 
abrasives or salt. Don’t mix different cleaning 
products - they may react together with 
hazardous results. Do not use a steam cleaner 
on your cooker.

If you want to move your cooker for cleaning, 
see the section called ‘

Moving your cooker

’.

All parts of the cooker can be cleaned with 
hot soapy water - but take care that no surplus 
water seeps into the appliance.

Stainless  Steel  Hob

Lift away pots or pans from hob. Remove pan 
supports from spillage area and carefully place 
in a sink of warm soapy water. Wipe loose 
debris from hob.
Avoid using any abrasive cleaners including 
cream cleaners, e.g. Cif, on brushed Stainless 
Steel surfaces. For best results use a liquid 
detergent e.g. Domestos Multi Surface Cleaner.
Rinse with cold water and thoroughly dry 
with a clean, soft cloth. Ensure all parts are dry 
before repositioning.

Hotplate  burners

The burner heads and caps can be removed 
for cleaning. Make sure they are absolutely dry 
before replacing.

Burner head

Burner Base

When fitting burner head, ensure this locates 
properly within the base.

Check burner ports are not blocked. If blockage 
occurs, remove stubborn particles using a 
piece of fuse wire.

Glide-Out™Grill

Before  you  remove  any  of  the  grill  parts  for 

cleaning  make  sure  that  they  are  cool.

The  grill  pan  and  grid  should  be  washed  in  hot 

soapy  water.  After  grilling  meats  or  any  foods 

that  soil,  leave  to  soak  for  a  few  minutes  in  the 

sink  immediately  after  use.  Stubborn  particles 

may  be  removed  from  the  grid  by  using  a 

nylon  brush.  Alternatively  the  grill  pan  can  be 

washed  in  a  dish  washer

To remove the grill pan support frame, pull the 
grill pan forward.

Lift the grill pan clear of the support frame.
The support frame is held to the side rails by 
two clips on each side.

For each side , support the side rail with one 
hand and with the other hand lift the frame up 
and out of the  side clips.

Summary of Contents for 210 GEO T DL





































Reviews: