Falcon Classic Deluxe, User'S Manual & Installation Instructions

WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON

Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have finished.

33

2.5  To Change a Hotplate Burner Thermocouple

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel and hotplate (see 1.2 & 2.1).
Unplug the FSD lead from the rear of the tap.
The thermocouple sits in a hole that has a slot at one 

side. Ensure that the thermocouple is cool. Turn the 

thermocouple so that the earth lead (no sleeve) is in line 

with the slot. Lift the thermocouple clear of the hole.
Reassemble in reverse order. 

2.6  To Remove or Change a Hotplate Burner

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the hotplate top (see 2.1). Remove the control 

panel (see 1.2).
The burners except the right hand wok burner 

are mounted on support struts. For these burners, 

disconnect the burner feed pipes at the burner. Remove 

the screws at the front and rear holding the support 

struts. Lift the strut and burners clear. The burners are 

fixed to the support struts with 2 screws. Remove the 

appropriate burner and fit the new one. Reassemble in 

reverse order. Check burner operation is satisfactory.
Right hand Wok burner
 Disconnect the burner feed pipes at the burner. Fit the 

new one and reassemble in reverse order. Check burner 

operation is satisfactory.

3 Control

3.1  To Change the Ignition Generator

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Change the hotplate tap as detailed in 2.2

3.2  To Replace the Light Switch

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.2).

Note: 

The old switch may be destroyed during removal. 

Remove the old switch from its bezel by gripping the 

switch body behind the control panel and twisting 

sharply. Remove the switch bezel by folding back its 

locking wings and pushing forward.
Fit the new bezel to the control panel by first lining up 

the raised key on its body with the cut-out in the control 

panel and pushing it in from the front.
Assemble the new switch to the bezel by lining up the 

key sections and pushing home. Fit the new button by 

pushing in from the front.
Replace the control panel in reverse order and test for 

correct operation.

3.3  To Remove the Electronic Timer

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Pull off the timer control button(s) and remove the 

control panel (see 1.2).
Remove the timer/mounting bracket assembly from the 

control panel by removing the fixing screws.
Remove the timer from its mounting bracket by 

depressing the plastic lugs on the timer case, at the 

same time pulling the unit forward.
Reassemble in reverse order. When replacing the leads, 

refer to the wiring diagram in this manual. Check the 

operation of the timer.

4 Grill

4.1  To Replace the Grill Controller

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the control panel (see 1.2) and hotplate top 

(see 2.1). Disconnect the wiring from the controller. 

Remove the 2 screws holding the controller to the 

mounting panel. 
Fit the new controller and reassemble in reverse order. 

Check for correct operation.

4.2  To Remove the Grill Element

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove grill pan from inside the grill compartment; 

remove the enamelled front shield from the grill roof, by 

undoing the 2 screws and washers.
Remove the 2 screws and washers securing the grill 

element front support. Remove the screws from the grill 

element.
Lift the element out carefully, disconnecting the leads 

from the element terminals (noting their position). 
If it is not possible to disconnect the leads in this way, 

pull the cooker forward to gain access to the rear, 

remove the screws securing the electric cover to the 

back sheet, remove the cover and disconnect the 

terminals from the rear.
Fit the new element and reassemble in reverse order. 

Check the operation of the grill.

5 Ovens

5.1   To Replace an Oven Thermostat

DISCONNECT FROM THE ELECTRICITY SUPPLY.

Remove the handrail (see 1.1), control panel (see 1.2) 

and hotplate top (see 2.1). Open the oven doors and 

remove the oven furniture.

Left-hand oven

From inside the oven remove the two screws holding 

the thermostat phial to the oven fan cover at the rear of 

the oven.
Remove the four screws that secure the fan cover 

(Fig.9-5)

 then remove the fan cover.