background image

9

 

 

Griddling 

Note that the centre of the pan is hotter than the edges when griddling. 

Simmering and Stewing 

Lid can be left slightly ajar if a gentle simmer is desired. As mentioned in griddling, the centre 
of the pan is hotter so the content may tend to stick to the pan more around the middle.  

 

 

CLEANING AND MAINTENANCE 

 

All  surfaces  are  easier  to  clean  if  spillage  is  removed  before  it  becomes  burnt  on  and  if 

appliance is cleaned daily. 

CAUTION:

  Failure  due  to  lack  of  proper  cleaning  is  not  covered  by 

warranty. 

 

 

BEFORE  ANY  CLEANING  IS  UNDERTAKEN,  ENSURE  ISOLATING  COCK  IS  TURNED 
OFF AND CANNOT BE INADVERTENTLY TURNED ON. 

WARNING 

– DO NOT ATTEMPT TO CLEAN THIS APPLIANCE WITH A JET OF WATER 

OR STEAM CLEAN. 

Clean pan as soon as possible after use with hot water and detergent. Soap filled steel wool 
pads may be used to remove stubborn deposits. After cleaning, empty water from pan using 
the pan tilting handle to lift the pan. 

Do  not  use  proprietary  cleaners,  especially  those  with  a  high  caustic  content  on  appliance 
surfaces.  This  is  particularly  important  when  appliance  is  hot.  Such  cleaners  can  cause 
serious damage or discolouration and only a soap or detergent solution should be used. 

 

 

 

 

SPECIFICATION 

 

Summary of Contents for Dominator Plus


























Reviews: