background image

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS 

This guide contains important instructions which must be followed during the maintenance of
this UPS and its batteries. Please read all instructions before operating this equipment and
save this guide for future reference.

Servicing of batteries should be performed by personnel knowledgeable of batteries
and the required precautions.  Keep unauthorized personnel away from batteries.
When replacing the UPS batteries, use the same number and type of batteries.

High voltage exists within the unit, which could cause electrical shock.  Always unplug
this UPS and remove the UPS battery fuse (if present) prior to attempting battery
replacement.

This UPS contains its own energy source (batteries) and may have external battery
sources. The output receptacles may carry live voltage even when the UPS is not 
connected to an AC source. 

This UPS contains sealed maintenance-free batteries (VRLA).  When situated in a 
typical office environment, with the proper charging and limited cycling, the batteries
can last many years. In home, office or computer room environments, the batteries
should be replaced every three to five years. In critical applications replace the 
batteries every two years.

When replacing the UPS batteries use the same number and type of batteries. Exercise
extreme caution when servicing the 240Vdc batteries in the UPS and External Battery
Banks due to the risk of electrocution.

 

The batteries approved for the Falcon SG 5 & 6 UPS models are as follows: 
20 pieces of Yuasa/Enersys NP7-12, 7Amp Hour, 12Vdc VRLA Type Battery (240Vdc) or
20 pieces of CSB GP 1272 F2, 7.2 Amp Hour, 12Vdc VRLA Type Battery (240Vdc)

Fror reference, the batteries approved for the Falcon SG 5 & 6 Extended Battery Bank
models are as follows: 
40 pieces of Yuasa/Enersys NP7-12, 7Amp Hour, 12Vdc VRLA Type Battery (240Vdc) or
40 pieces of CSB GP 1272 F2, 7.2 Amp Hour, 12Vdc VRLA Type Battery (240Vdc

NEVER

dispose of batteries in a fire, as batteries will explode.

NEVER

dispose of used batteries in the trash or landfill as it is a violation of federal 

and state laws. 

The batteries must be recycled. 

For battery recycling information, please contact:

www.enersysinc.com/default.asp

or 

www.csb-battery.com/Top/english/recycle_state.htm

for the name and address of the nearest battery recycling facility. 

CAUTION

CAUTION

CAUTION

CAUTION

CAUTION

1

Summary of Contents for SG5K-1TX











Reviews: