background image

G1528  

 

 

 

 

 

 

 

STEAKHOUSE PLUS GRILL 
 

INSTALLATION and  
SERVICING INSTRUCTIONS 

 

These appliances must be installed and serviced by a competent person as stipulated 
by the Gas Safety (Installation & Use) Regulations. 
 
IMPORTANT 

The installer must ensure that the installation of the appliance is in conformity with these 
instructions and National Regulations in force at the time of installation. Particular attention 
MUST be paid to 

– 

 

Gas Safety (Installation & Use) Regulations   Health and Safety at Work, etc. Act 
Local and National Building Regulations        Fire Precautions Act 
Detailed recommendations are contained in the Institute of Gas Engineers published           
documents: IGE/UP/1, IGE/UP/2 BS6173 and BS5440 
 

These appliances have been CE-marked on the basis of compliance with the Gas Appliance 
Directive for the Countries, Gas Types and Pressures as stated on the Data Plate. 
 

WARNING - TO PREVENT SHOCKS, ALL APPLIANCES WHETHER GAS OR 
ELECTRIC, MUST BE EARTHED 
 

On completion of the installation, these instructions should be left with the Engineer-in-
Charge for reference during servicing. Further to this, the Users Instructions should be 
handed over to the User, having had a demonstration of the operation and cleaning of the 
appliance.  
 

IT IS MOST IMPORTANT THAT THESE INSTRUCTIONS BE CONSULTED BEFORE 
INSTALLING AND COMMISSIONING THIS APPLIANCE. FAILURE TO COMPLY WITH 
THE SPECIFIED PROCEDURES MAY RESULT IN DAMAGE OR THE NEED FOR A 
SERVICE CALL. 
 
PREVENTATIVE MAINTENANCE CONTRACT 

In order to obtain maximum performance from this unit we would recommend that a 
Maintenance Contract be arranged with SERVICELINE. Visits may then be made at agreed 
intervals to carry out adjustments and repairs. A quotation will be given upon request to the 
contact numbers below. 
 

WEEE Directive Registration No. WEE/DC0059TT/PRO

 

At end of unit life, dispose of appliance and any replacement parts in a safe 
manner, via a licensed waste handler. 
Units are designed to be dismantled easily and recycling of all material is 
encouraged whenever practicable. 
 

Falcon Foodservice Equipment

 

Head Office and Works 
Wallace View, Hillfoots Road, Stirling. FK9 5PY. Scotland. 
Serviceline  PHONE: 01438 363 000 

T100702 Ref.4 

Summary of Contents for STEAKHOUSE PLUS G1528













Reviews: