31
DuraTech Stainless Cable SRL’s (“S-series”)
Model #s: 7226S, 7227S, 7229S, 7232S, 7267S, 7268S,
7211S, 7212S, 7213S
Component Material
Rating
Housing Cast/Machined
Aluminum Alloy
n/a
Drum
Cast/Machined Aluminum Alloy
n/a
Main Shaft
CNC Machined Aluminum Alloy
n/a
Pawls/Ratchet
Manganese Bronze Alloy
n/a
Pressure Plate
Chro-Moly Alloy Steel
n/a
Cable
3/16” 7 x 19 Stainless Steel
4,000 lbs
Attachment Carabiner
Chro-Moly Alloy Steel
5,000 lbs
Overall static strength:
> 3,000 lbs
* Arrest Forces:
< 800 lbs
* Deceleration Distance:
< 24”
Maximum Capacity:
310 lbs
* When tested in accordance with ANSI Z359.1-2007
DuraTech Stainless Cable SRL’s (“SS-series”)
Model #s: 7226SS, 7227SS, 7232SS, 7266SS, 7268SS, 726575SS
Component Material
Rating
Housing Cast/Machined
Aluminum Alloy
n/a
Drum
Cast/Machined Aluminum Alloy
n/a
Main Shaft
CNC Machined Aluminum Alloy
n/a
Pawls/Ratchet
Manganese Bronze Alloy
n/a
Pressure Plate
Stainless Steel
n/a
Cable
3/16” 7 x 19 Stainless Steel
4,000 lbs
Attachment Carabiner
Stainless Steel
5,000 lbs
Overall static strength:
> 3,000 lbs
* Arrest Forces:
< 800 lbs
* Deceleration Distance:
< 24”
Maximum Capacity:
310 lbs
* When tested in accordance with ANSI Z359.1-2007
DuraTech Heavyweight Cable SRL’s (“HW-series”)
Model #s: 7226HW, 7227HW, 7232HW, 7265HW, 7268HW,
7211S, 7212S, 7213S
Component Material
Rating
Housing Cast/Machined
Aluminum Alloy
n/a
Drum
Cast/Machined Aluminum Alloy
n/a
Main Shaft
CNC Machined Aluminum Alloy
n/a
Pawls/Ratchet
Manganese Bronze Alloy
n/a
Pressure Plate
Chro-Moly Alloy Steel
n/a
Cable
3/16” 7 x 19 Galvanized Steel
4,000 lbs
Attachment Carabiner
Chro-Moly Alloy Steel
5,000 lbs
Overall static strength:
> 3,000 lbs
* Arrest Forces:
< 900 lbs
* Deceleration Distance:
< 30”
Maximum Capacity:
400 lbs
* When tested in accordance with ANSI Z359.1-2007
32
10.3: Labels and Markings
Labels are an important part of the product and should be referred to
often to keep these important details fresh. The labels located on the
front of the housing (shown in figure 10.1) identify the product and
provide key details with respect to the products rating. There is also
information pertaining to the use of the product along with critical
warnings. Failure to heed these warnings may result in serious injury or
death.
The labels on the back of the SRL housing have information
regarding the proper installation and inspection of this product. These
are shown in figure 10.2.
Figure 10.3 is the service label. Be sure to use a permanent marker
to log the date that the product is put into service. This label should be
inspected every six months during the competent person inspection to
ensure that the product is within the recertification parameters discussed
in Section 9 of this manual.
The labels shown below must be present on the product and must be
legible. If they are not, remove the product from service.
Figure 10.1: Located on front housing
