background image

 

This product is to be used as part of a complete fall arrest system in 
accordance with industry-recognized best-practices and your 
employer’s fall protection plan, as required by the Occupational 
Health and Safety Administration.  Be aware of your employer’s fall 
protection plan and rescue plan.  Be aware of the specific fall 
hazards on your jobsite and work deliberately to avoid these 
hazards in the course of your work.  Also be aware of hazards and 
obstructions in your fall path, and work with your employer to 
eliminate these hazards where possible.  Failure to be aware of and 
to address these hazards may result in serious injury or death. 
 

Do’s and Don’ts 

 

 

Do

 use this device only with compatible components of a 

comprehensive fall arrest system. 

 

Do

 use this device only in a system which limits free fall distance 

to 5 ft or less. 

 

Do

 use extreme caution when rigging this device. 

 

Do

 rig this device to avoid the hazards of “swing fall” (see 

Section 2.9) 

 

Do

 inspect the entire lifeline of the SRL for cuts, abrasions, 

kinks, wear, or other damage. 

 

Do

 wear gloves when handling wire rope. 

 

Do

 inspect the load indicating swivel snap hook for the red fall 

indicator band. 

 

Do

 use this device only when your clearance distance is a 

minimum of 2 ft AFTER you have calculated the total fall 
distance (see section 2.8 for details on clear fall distances). 

 

Do

 check the brake mechanism by “hand locking” the device 

before each use. Pull out 4 ft of line from the SRL and give a 
swift pull to activate the brake. Then allow the line to retract 
SLOWLY back into housing. 

 

Do 

make compatible connections (see Advisory #3 at the end of 

this Section). 

 

Do

 use a tagline, if the SRL is remotely mounted, to access 

cable and control the retraction speed of cable after use (see 
Section 7) 

 

Do

 call FallTech if the device is damaged, does not pass 

inspection (see Section 6), or has arrested a fall. 

 
 

 

Don’t

 use this device as a load arrestor when hoisting materials 

or equipment. 

 

 

Don’t

 use this device if it has been exposed to corrosion, 

chemicals, excessive heat, flames, or electrical charge or shows 
signs of any physical damage or deformation. 

 

Don’t

 allow the lifeline to wrap around your body. Severe injury 

or death could result.

 

 

Don’t

 loop the lifeline under an arm or leg, turn toward the SRL 

and walk toward the SRL. If a fall should occur while the line is 
under an arm or leg, severe injury may result. 

 

Don’t

 move too quickly when using this device. The brake may 

activate and cause the loss of footing or a fall. 

 

Don’t

 leave lifeline exposed when the device is not in use. 

Retract lifeline fully into the housing using a tagline when needed 

 

Don’t

 use oil on the carabiner or any part of the device, except 

the cable. If needed, use only 100% silicone lubricant for the 
load indicating swivel snap hook. 

 

Don’t

 use any type of cable in this device if you are working near 

high voltage power lines or other energized electrical equipment. 
Extreme caution must be taken when working under these 
conditions, even when equipped with a FallTech approved high-
tech rope 

 

Don’t

 use this device if you are pregnant, a minor, or have a 

reduced tolerance to fall forces by reason of age, physical 
medical condition, or other pre-existing disorders. 

 

Don’t

 use this device if you weigh less than 75 lbs. 

 

Don’t

 use this device if your total combined weight (body, 

clothes, tools, etc) exceeds 310 lbs.  

Model #’s ending in HW 

are approved for a maximum capacity of 400 lbs.

 

 

Don’t

 release the lifeline allowing it to “free wheel” (see Section 

7) or retract back uncontrolled into the device. 

 

Don’

t attempt to open, repair or alter this device in any way 

unless trained and certified to do so by FallTech. 

 

Don’t

 knot, clamp, or rig lifeline in any fashion as to inhibit its 

automatic retraction function. 

 

Don’t

 use the device if it does not lock or retract automatically

.

 

 

Don’t 

use this SRL with the cable fully extended.  This product 

has a red coating on the cable.  If this red cover is exposed, then 
your operating at the maximum allowable extension of the cable.  
DO NOT ATTEMPT TO PULL ADDITIONAL CABLE OUT OF 
THE UNIT! 

 

Advisory #1:  Further Reading 

 
     If you have access to the internet, please go to www.osha.gov.  
This website is an exceptional resource, and has a great deal of 
information which is easy to access.  Use the search field to find 
information on fall arrest, including standards, news, 

Summary of Contents for DuraTech SRL Series



















Reviews: