background image

 

Advisory #2:  Proper product selection 

 
     Product selection is an important element of fall protection.  Fall 
Arrest products are like any other tools that you may use in the 
course of your work – there is a proper tool for every application.  
You may find that while this product is suitable for some 
applications, it may not be suitable for others.  Please be sure to 
pay close attention to sections 2, 3, and 4, for greater detail on this 
point. 
 

Advisory #3:  Connector Compatibility 

 
     Making compatible connections may mean the difference 
between life and death.  Connectors (snap hooks, rebar hooks and 
carabiners), must be of the locking type and require two distinct 
actions to open the gate.  Your connectors must be sized and 
shaped so that the rings or structural members to which they are 
attached will not pose a risk of forcing the gate open, and must fully 
captivate the connector so that it cannot become disengaged, slide 
or shift during use or in the event of a fall. 
 
     Certain connections are forbidden and should never be 
attempted with this product or any other unless there is a specific 
allowance in the manufacturer’s instructions.  Forbidden 
connections include, but are not limited to: 
 

 

Two or more connectors to one d-ring are a forbidden 
connection. 

 

A connection that rests on or loads the gate is a forbidden 
connection. 

 

A connection that does not allow the gate to close and lock 
is a forbidden connection. 

 

Two or more connectors attached to one another are a 
forbidden connection. 

 

Connecting directly to webbing, rope, cable (wire rope) is a 
forbidden connection. 

 

Connecting directly to a horizontal lifeline is a forbidden 
connection. 

 

Tie-back with your FallTech Web SRL is a forbidden 
connection. 

 

Connecting to any ring or structure that does not fully 
captivate and completely restrict the movement your 
connector is a forbidden connection. 

 
 
 

 

 
Section 2:  ABCD’s 

 

     Every Personal Fall Arrest System consists of four basic elements – 
Anchorage, Body-wear, Connectors/Connecting Devices and 
Deceleration Devices.  Each of these four elements is discussed in 
greater detail below.  If, after reading though this section, you do not fully 
understand these items and how they work together to form a compatible 
fall arrest system, please be sure to have this explained to you by a 
Competent Person. 
 
     It is absolutely critical that you be familiar with the proper wear and/or 
use of each component of your Personal Fall Arrest System (PFAS).  
Failure to read, understand and adhere to instructional materials and 
warnings provided with each of these components could lead to a 
catastrophic failure of your PFAS, resulting in serious injury or death. 

 
2.1:  Anchorage 
 
     

The selection of an anchor point and anchorage connector is critical 

to the successful function of any Personal Fall Arrest System (PFAS).  
OSHA 1926.502 (d) (15) states that:   

      
“Anchorages used for attachment of personal fall arrest equipment shall 
be independent of any anchorage being used to support or suspend 
platforms and capable of supporting at least 5,000 pounds (22.2 kN) per 
employee attached, or shall be designed, installed, and used as follows:  
as part of a complete personal fall arrest system which maintains a 
safety factor of at least two; and under the supervision of a qualified 
person.” 
 
     

Ensure that the structure to which you are attaching your anchorage 

connector is capable of meeting the above requirements and that your 
anchorage connector is installed in accordance with the manufacturer’s 
instructions.  Also be sure to check that the anchorage connector is 
compatible with your 

FallTech Webr

 SRL and that it securely retains the 

SRL without inhibiting its function.  If you are unable to determine 
whether your SRL and your anchorage are compatible, please 
immediately consult with a competent person or your immediate 
supervisor.  For more details on anchorages, please see section 5 of this 
instruction manual. 
 

2.2:  Body-wear 
 

     Body wear for any application where this SRL is to be used will be 
defined as a full body harness specifically manufactured for fall arrest.  

Summary of Contents for Web SRL 7262









































Reviews: