FALMEC Circle.Tech Levante 120 Isola White, Instruction Booklet

13

ENGLISH

 MAINTENANCE

Before cleaning or carrying out maintenance operations, disconnect the 
equipment by removing the plug or switching off the main switch.
Do not use detergents containing abrasive, acidic or corrosive substances 
or abrasive cloths.

Regular maintenance guarantees proper operation and performance over time.
Special attention is to be paid to the 

metal anti-grease filters 

: frequent cleaning of the 

filters and their supports ensures that no flammable grease is accumulated.

CLEANING OF EXTERNAL SURFACES

You are advised to clean the external surfaces of the hood 

at least once every 15 days

to 

prevent oily substances and grease from sticking to them. To clean the brushed stainless 
steel hood, the Manufacturer recommends using "Magic Steel" wipes.
Alternatively 

and for all the other types of surfaces

, it can be cleaned using a damp cloth, 

slightly moistened with mild, liquid detergent or denatured alcohol.
Complete cleaning by rinsing well and drying with soft cloths. 

Do not use too much moisture or water around the push button control 
panel and lighting devices in order to prevent humidity from reaching 
electronic parts.

The glass panels can only be cleaned with specific, non-corrosive or non-abrasive deter-
gents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with these instructions.

CLEANING OF INTERNAL SURFACES

Do not clean electrical parts, or parts related to the motor inside the hood, 
with liquids or solvents.

For the internal metal parts, see the previous paragraph.

METAL ANTI-GREASE FILTERS

It is advised to 

frequently

 wash the metal filters (

at least once a month

) leaving them to 

soak in boiling water and cleaning solution for 1 hour, taking care not to bend them.
Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reassembling them.
Washing in a dishwasher is permitted, however, it may cause the filter material to darken: to 
reduce the possibility of this problem from happening, use low-temperature washes (55°C 
max.).
To extract and insert the metal anti-grease filters see the assembly instructions.

HOOD MOVEMENT SETUP

Press button  

 for 10 seconds

When SETUP is started, all LEDs light up

The hood moves slowly upwards 
until it reaches the upper limit 
switch

The hood moves downwards 
until it reaches the lower limit 
switch.
If you want to set the hood stop 
before it reaches the lower limit 
switch, which represents the 
maximum lowering, press + or 

- on the button panel or 

 or 

 or 

 USING THE RADIO CONTROL

WARNINGS!:
Place the hood away from sources of electromagnetic 
waves (e.g. microwave ovens), which could interfere 

with the radio control and with the hood electronics. The maxi-
mum operating distance is 5 metres, that may vary according to 
the presence of electromagnetic interferences. 
Radio control operated at 433.92MHz.
The radio control consists of two parts:
- the receiver built into the hood;
- the transmitter shown here in the figure.

DESCRIPTION OF TRANSMITTING COMMANDS

Press
briefly

UP

Motor switch-on and speed increase from 1 to 4. Speed 4 is 
only active for a few minutes.

Pressure
prolonged

Lifting the hood

Activated only with the fan not working.
Stop:
- when the upper microswitch is reached

- pressing the 

 or 

 or 

.

Press
briefly

DOWN

Decremento velocità e spegnimento motore

Pressure
prolonged

Lowering the hood

Activated only with the fan not working.
Stop:
- when the lower microswitch is reached

- pressing the  

 or 

 or 

.

Press
briefly

Accensione / spegnimento luce

Pressure
prolonged

Cambio tonalità della luce da 2700K a 5600K

Press
briefly

TIMER: 

Autospegnimento del motore dopo 15min.

The function is deactivated if the  

 or 

 button is pres-

sed.

RADIO CONTROL CODE CHANGE

With only one radio control, go directly to point 2.
With several radio controls in the same room, a new code can be created by following the 
procedure below.

Disconnect the power to the hood before starting the procedure.

1) - CREATE A NEW CODE

The procedure is to be carried out on the radio control.

•

 Press 

LIGHT 

 and TIMER 

 simultaneously until the display starts flashing.

•

 Press 

DOWN 

 on the radio control: saving is confirmed by three brief flashes of the 

display. The new code cancels and replaces the previous default code. 

Reconnect the hood to the electrical power supply, making sure that the 
lights and motor are off. 

2A) - ASSOCIATING THE RADIO CONTROL WITH THE HOOD
           USING THE ELECTRONIC PUSHBUTTON PANEL
 

press TIMER (

)

on the hood pushbutton panel

 for 2 seconds:

the red LED lights up. 
press any key on the radio control within 10 seconds. . 

RESTORING DEFAULT CODE

the procedure is to be carried out if the hood is disposed of, sold or transferred.

Disconnect the power to the hood before starting the procedure.

•

 Press 

UP 

 and DOWN 

 simultaneously on the radio control for more than 5 sec-

onds: reset is confirmed by three brief flashes of the display. 

•

  Reconnect the hood to the electrical power supply.

•

  Proceed with associating the hood and the radio control, as described in point 2.