ENGLISH
19
24h
Speed 1 button
With LED on (speed 1 already running):
• Pressing this key
will switch off the hood
motor and the LED associated with the key
With LED off:
• A
short
press
starts or sets the hood at speed 1
(the function starts when the key is released); when speed 1 is running, the relative
LED lights up.
• With the motor off, a
long press (at least 3 seconds)
will start the recirculation function: in this mode (for 24 hours), the hood runs an
operating cycle which involves starting the motor at the 1st speed for 1 hour, followed by 3 hours with the motor down. This cycle is
repeated for 24 hours, until timeout. For these 24 hours, the LED flashes, meaning that the recirculation function is running. With this
feature enabled, you CANNOT select other speeds.
• To deactivate this function, keep the relative key pressed for at least 3 seconds.
Speed 2 button
With LED on (speed 2 already running):
• Nothing will happen when this key is pressed. To
switch the hood off
firstly select speed 1, then press the "speed 1 button" again.
With the LED off and a speed on:
• Press the key (
long or not
) to
set the hood on speed 2
. When speed 2 is running the relative LED will light up.
With the LED off and NO speed on:
• Nothing will happen when this key is pressed.
Speed 3 button
With LED on (speed 3 already running):
• Nothing will happen when this key is pressed. To
switch the hood off
firstly select speed 1, then press the "speed 1 button" again.
With the LED off and a speed on:
• Press the key (
long or not
) to set
the hood on speed 3
. When speed 3 is running the relative LED will light up.
With the LED off and NO speed on:
• Nothing will happen when this key is pressed.
Speed 4 button
With LED on (speed 4 already running):
• Nothing will happen when this key is pressed. To
switch the hood off
firstly select speed 1, then press the "speed 1 button" again.
With the LED off and a speed on:
• Press the key (
long or not
) to set
the hood on speed 4
. When speed 4 is running the relative LED will start flashing; the 4th, or inten-
sive, speed is timed and after approximately 7 minutes the motor will automatically switch to 3rd speed.
With the LED off and NO speed on:
• Nothing will happen when this key is pressed.
Light Button
Light:
• By briefly pressing the key (the back-lit button), you turn the light on and off.
LIGHTING
The hood has fluorescent lamp lighting.
If the lamp ever needs to be replaced:
•
disconnect the appliance from the electrical mains power supply by unplugging it or turning off the main switch;
•
open the external suction panel (see instructions
G
on page
6
);
Phase
L
page 6
• remove the covering element (
N
) (Fig.
1
and
2
);
• take out the blown fluorescent tube (
M
) (Fig.
3
and
4
);
• put in a new fluorescent lamp by performing, in reverse order, the operations described in Fig.
3
and
4
;
The new fluorescent lamp must be identical to the old one!
• put the covering element back in (
N
) performing, in reverse order, the operations described in Fig.
1
and
2
;
• connect the appliance back up to the electrical power mains.
Summary of Contents for imago
