SECURITY MEASURES
*Please observe the following rules for the safe use of the device.
1.
Use the correct type of electrical cord. The plug must be rated for at
least 12 amps. Connecting the machine to the same outlet as other
electrical products may cause overheating and fire.
2.
Place the machine on a solid, level surface. Place the machine on a
solid, level floor.
3.
Avoid contact of the machine with sources of high temperature or
humidity. Install the machine away from sources of heat or steam such
as a gas burner or oil heater, as well as sinks and other places where
water can get on the machine.
4.
Ensure sufficient distance from the device to the wall. This distance
must be at least 15 cm in order not to block the air supply to the rear
panel.
5.
If the electrical cord is damaged, please contact the service center to
replace it.
Grounding
Grounding is necessary to prevent electric shock.
The protective earth electrode must be buried in the ground to a depth
with sufficient moisture (more than 30 cm)
If there is a ground bus, use it.
Use a short circuit protection device if it is difficult to establish a ground
connection.
Consult an electrician for grounding.
Installation
Do not use excessive force when unpacking, so as not to damage the
surface of the machine.
Do not tilt the machine more than 45° when transporting. Do not plug the
machine into the mains for one hour after moving it to another location.
Always turn on the electricity only after filling the machine with water.
Connecting to the electrical network without water in the hot and cold
water tanks will lead to the failure of the device.
USAGE
Machine Operations
Please observe the following rules when installing:
1.
Make sure you are using the correct type of electrical cord. Remove all
sources of heat and water from the installation site. Install the machine
on a horizontal floor. Keep a distance of 15 cm from the wall.
2.
Connect the appliance to the electrical network only after filling the hot
and cold water tanks with water. Place the water bottle (use the
designated bottles) on top of the machine. Bubbles that appear inside the
bottle indicate that water is entering the cold and hot water tanks. After
bubbles stop forming, keep the hot water faucet pressed until water
comes out of the faucet. Plug in the power cord. Connecting to the
network without filling the tanks with water can damage the device.
3.
Turn on the hot water switch on the rear panel. After turning on the
electric power, it takes approximately 15 minutes for heating (70°C-90°C)
and 30 minutes for cooling (4°C-12°C). To use cold water only, turn off
the hot water switch.
1.
4. To replace an empty bottle, pull it firmly up and out of the body. Use only
specially designed bottles. Never use tap water, boiled water, or any other
type of drinking water. Connect the appliance to the electrical network only
after filling the hot and cold water tanks with water
Summary of Contents for WONBONG WBF-1000 LA
