background image

then both brushes and the earth brush shall be replaced at the same time. The brushes shall 
only be replaced by a suitably qualified person.
20. An all-pole disconnection incorporated in the fixed wiring is to be provided, such as an 
all-pole switch or a supply cord fitted with a plug.
21. The light source in light kit is not replaceable; when the light source reaches its end of life 
the whole light kit shall be replaced by manufacture, his service agent or a qualified person.
22. The max operating temperature for the fan is 40 degree °C. Keep the fan away from any 
heat sources, like fire place, heater and stove.

IMPORTANT NOTE: 

The important safeguards and instructions given in this manual are not meant to cover 

all possible conditions and situations that may occur. It must be understood that common 

sense, caution and care are factors which cannot be built into any product.

CAUTION: 

Do not ingest battery - Chemical burn hazard. 
The remote supplied with this product (remote/Smart model) contains AAA batteries. If 
the battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to 
death. 
Keep the new and used batteries away from children. Examine devices and make sure the 
battery compartment is secure. 
If the battery compartment does not close securely, stop using the product and keep it away 
from children. 
If you think batteries might have been swallowed or placed inside any part of the body, seek 
immediate medical attention.
 Call the Poisons Information Centre on 13 11 26 or go to a hospital emergency room. 
Do not let the child eat or drink and do not induce vomiting. Dispose of used button 
batteries immediately. 
Flat batteries can still be dangerous. 
The battery supplied with this product is not to be recharged. 
Different types of batteries or new and used batteries are not to be mixed. Battery to be 
inserted with the correct polarity. + for positive, - for negative. 
Exhausted batteries are to be removed from the appliance and safely disposed of. 
If the appliance is to be stored unused for a long period, the batteries should be removed. 
Dispose of used button batteries immediately. 
Flat batteries can still be dangerous. the supply terminals are not to be short-circuited.

FAULT FINDER:

Always check the “Trouble Shooting Checklist” included in this booklet before seeking 
warranty claim.
Mechanical noise may be noticed on installation. Allow at least 8 hours settling-in period.
Some fans may wobble more than others, even if they are identical. This does not necessarily 
indicate a fault.

PREPARATION:

1. Unpack your ceiling fan carefully, then remove all parts and components, and lay on 
a cloth or soft surface to avoid damage. DO NOT lay the motor housing on its side, the 
housing may get damaged.
2. Before commencing installation, check that all parts are included.

NB: You may need to remove all foam packaging material to ensure there are no missing 
parts.

2

Summary of Contents for CFFCST2LWHSMR















Reviews: