background image

 

18.

 

If it is necessary to replace the live or neutral brushes to ensure operation of the motor then 
both brushes and the earth brush shall be replaced at the same time. The brushes shall only be 
replaced by a suitably qualified person. 

19.

 

An all-pole disconnection incorporated in the fixed wiring is to be provided, such as an all-pole 
switch or a supply cord fitted with a plug. 

20.

 

The remote/receiver included is intended to be used with this fan and associated light component 
ONLY and is not compatible with any other lighting and/or any other electrical device. Use of it in 
any way other than intended may result in damage to the fan, receiver and/or other devices and as 
such, will void warranty. 

21.

 

The LED light panel in light kit is user replaceable as it connects with 'Push Plug' wiring. 

It is user 

replaceable ONLY with Fanco certified replacement LED panels

. Using unauthorised parts may 

damage the fan, cause undesired results, or be a safety hazard. 

22.

 

The max operating temperature for the fan is 40°C. Keep the fan away from any heat sources, like 
fire place, heater and stove. 

23.

 

Reasonable ‘wear and tear’ is not covered under warranty. For comprehensive warranty terms & 

conditions visit 

fanco.com.au

  

 

IMPORTANT NOTE:  
The important safeguards and instructions given in this manual are not meant to cover all possible 
conditions and situations that may occur. It must be understood that common sense, caution and care 
are factors which cannot be built into any product. 

CAUTION: 

 

 

DO NOT

 ingest battery - Chemical burn hazard 

 

The remote supplied with this product contains 2xAAA batteries. If the battery is swallowed, it can 
cause severe internal burns in just 2 hours and can lead to death 

 

Keep the new and used batteries away from children. Examine devices regularly, and ensure the 
battery compartment is secure 
-

 

If the battery compartment does not close securely, stop using the product and keep it away 
from children 

 

If you think the batteries might have been swallowed or placed inside any part of the body, seek 
immediate medical attention 
-

 

Call the Poisons Information Centre on 

13 11 26

 or go to a hospital emergency room 

-

 

DO NOT

 let the child eat or drink or induce vomiting. Dispose of used button batteries 

immediately 

 

The batteries supplied with this product is not to be recharged 

 

Different types or new and used batteries are not to be mixed 

 

Battery to be inserted with the correct polarity; 

+

 for positive, 

-

 for negative 

 

Exhausted batteries are to be removed from the appliance and safely disposed of 

 

If the appliance is to be stored unused for a long period, the batteries should be removed 

 

Dispose of used button batteries immediately 

 

Flat batteries can still be dangerous. The supply terminals are not to be short-circuited 

FAULT FINDER:

 

Always check the “Trouble Shooting Checklist” included in this 

manual before seeking a warranty 

claim.  
A mechanical noise may be noticed on installation. Allow at least 8 hours settling-in period. 
Some fans may wobble more than others, even if they are identical. This does not necessarily 
indicate a fault. 

 

Summary of Contents for Infinity-ID DC

















Reviews: