background image

- 8 -

power supply 

100÷265 V AC

maximum load current (AC-1/AC-3) 

8 A/1.5 A

power consumption

staandby 

0.15 W

on 

0.6 W

control 

triggered N level

switch-on time (adjustable) 

1 s÷15 min.

power indication 

green LED

operation and movement direction indication 

red 2×LED

working temperature 

-25÷50°C

terminal 

2.5 mm² screw terminals

tightening torque 

0.4 Nm

dimensions 

1 module (18 mm)

mounting 

on TH-35 rail

protection level 

IP20

F&F products are covered by a 24-month warranty from the date 

of purchase. The warranty is only valid with proof of purchase. 

Contact your dealer or contact us directly.

F&F Filipowski sp. j. declares that the device is in conformity 

with the essential requirements of  The Low Voltage Directive 

(LVD)  2014/35/EU  and the Electromagnetic Compatibility (EMC) 

Directive 2014/30/UE. The CE Declaration of Conformity, along 

with the references to the standards in relation to which confor-

mity is declared, can be found at www.fif.com.pl on the product 

page: www.fif.com.pl from the product subpage.

Technical data 

Warranty

CE declaration

E220830

Summary of Contents for STR-3D









Reviews: