background image

12

Before discarding packaging materials, be certain all parts have been removed

Parts List

Model #FP3820RP

Ref. #

Description

Part #

1

Hanger Bracket Assembly

APG510BL

2

Downrod/Hanger Ball Assembly Containing:

ADR6BL

2a

Hanger Ball Assembly

2b

Downrod

2c

Hairpin Clip

2d

Clevis Pin

3

Ceiling Canopy

PG160BL

Fan Motor/Housing Assembly

4

Housing Assembly, Rustic Pine

AMH3828RP

4a

Motor Assembly

AMA3820SER

11

Housing Switch Cup/Adapter Assembly

AP3805BL

11a

Wiring Harness (part of Housing Switch Cup/Adapter assembly)

AP3830BL

5

Support Cable Bag Containing:

HWBSCABLE

Ceiling Support Cable

Cable Clamp

Flat Washer

Lag Bolt, 

3

/

8

˝

 x 2

˝

6

Hardware Bag Containing:

HDWFP3820

5

/

32

˝

 Threaded Rods (2)

5

/

32

˝

 External Lockwasher (2)

Knurled Knobs (2)

“L” Screwdriver

Chain Coupler

Chain Fob

Wire Connectors (4)

7

Blade Holder Mounting Hardware Bag Containing:

HDWBH3820

¼–20 x

 

14 mm Phillips Screws (11)

8

Blade Mounting Hardware Bag Containing:

HDWBM3820

Wood Phillips Pan-Head Screws, 

3

/

16

-24 x 15 mm & Fiber Washers (16)

Philips Screwdriver, 4

˝

9

Blade Holder - Black (Set of 5)

AP3810BL

10

Wood Blades (Set of 5)

AP3825RP

How To Order Parts

When ordering repair parts, always

give the following information:

• Part Number

• Part Description

• Fan Model Number

Contact your retail store for repair parts.

Summary of Contents for Alamosa FP3820RP















Reviews: